In order to drain the tank faster, a pump is installed near the tank exit. Determine how much power input is necessary to establish an average water velocity of 4 m/s when the tank is full at 2 m. diameter is 10cm

Q: A manufacturer states that their gear pump requires 0.85 hp to pump 9 gpm of oil (sg=0.90) with a…

A: The flow rate of the oil is, Q=9 gpm. The specific gravity of the oil is, SGo=0.90. The total heat…

Q: please explain how to get the friction factor

A: The objective of the question is to calculate the friction factor, the power supplied to the pump,…

Q: Find the discahrge through pipe having cross sectional area of 4 mm2 and velocity of flow is 3.31…

A: Given data : Velocity of flow V=3.31 m/s Cross sectional area A=4 mm2   To find : Discharge through…

Q: Define net positive suction head and required net positive suction head, and explain how these two…

A: The net positive suction head also called as the net positive suction head available or the actual…

Q: A 2-inch copper pipe connection was made from the basement to the second floor in the building. The…

A:

Q: A water tank with a very large cross-sectional area, open at the top, has a very small hole drilled…

A:

Q: 1 QUESTION 1 Consider a desired pump operating condition which adds 35 psi at a flowrate of 500 gpm…

A: Given data  Flow rate = 500 gpm Pressure = 35 psi Density = 62 lbm/ft^3 Find the pump head

Q: Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m ) is to be pumped through 50 m of pipe…

A:

Q: Problem 3 – Water from a large tank flows thru the pipe system shown at a rate of 10 ft³/s and…

A:

Q: Q5) A pump of 20 kW power is discharge oil to the over tank as shown in fig. (5). If the efficiency…

A:

Q: A pump with a design flow of 35m³/hr at 3000 rpm when delivers a head of 50 m. The NPSH, is 3m. What…

A:

Q: A tank 1.5 m stands on a trolly and is full of water. It has an orifice of diameter 0.1 m at 0.3m…

A: Given:h=1.5 md=0.1 mCd=0.6

Q: A water discharge of 8 m3 s is to flow through this horizontal pipe, which is 1 m in diameter. If…

A: Given Data⇒ Discharge Q=8m3s Horizontal Pipe Diameter of pipe(d)=1 m   Assumptions made in…

Q: Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m ) is to be pumped through 50 m of pipe…

A:

Q: There are three main categories of dynamic pumps. List and define them.

A: Dynamic pumps are typically the main pumps generally used for large flows with lower pressures. They…

Q: Water flows into a house by means of a pipe with an inner diameter of 2,4cm, absolute pressure is…

A:

Q: Aa certain hydro-power station has a head of 500m between the upper and lower reservior. A.…

A: The given information in the problem is shown in the following attached image:

Q: In figure, Bernoulli's equation- ?between point 1 and 2 is Punp

A:

Q: The pressure after the pump in a 15-cm internal diameter smooth pump conducting water is 137.895 kPa…

A:

Q: The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of…

A:

Q: Q. No 3). A water supply pipe line is designed to supplying water to a nearby city. Determine…

A:

Q: Water flows from a large close tank, through pipe length 15m, diameter (30mm) and exits with…

A:

Q: Using the pump selection table below to determine the best pump for the given condition: A flow of…

A: Given data as per the question Flow rate =150 m3/h =41.6667 L/S Head =50 m

Q: 010. Water is pumped from the large tank shown in Fig. The head loss is known to be equal to 4v/2g…

A: The head loss, hL=4*V22gPump head, hp=20-4Q2Pipe area, A=0.10 ft2Elevation difference, ∆Z=Z1-Z2=13…

Q: Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m ) is to be pumped through 50 m of pipe…

A: for solution refer below images. Note:- since loss coefficient for abrupt expansion is not given i…

Q: if efficiency is Go7. : Find the Power of pump . to flow water at 360LIS and fizo.02, f2=0.021…

A:

Q: A pipe experienced a total head loss of 15 m, determine the pressure difference from its starting…

A:

Q: each pipe may be taken 0.03. 100 mm diameter, 200 m length Atmosphere B 100 mm diameter, 100m length…

A: Calculated discharge in each pipe.

Q: A Sluice gate Is a device that is flted in a Sluice fluid canal to qpersrte cand control the fluid…

A:

Q: What is the velocity of the pipe center (m/s)? Given that h3%-88.3 cm h3 h2 =7 cm h =3 cm] Water

A: hps=88.3+7hps=95.3 cm or 0.953 mhp=7 cm or 0.07 m apply bernoulli's equation between 1 and…

Q: Francis and Kaplan turbines are often provided with drafttubes, which lead the exit fl ow into the…

A: A draft tube can be defined as a pipe of gradually increasing area that connects the outlet of the…

Q: For transferring of water, a pump is installed in the height of 3 m above the surface of the water.…

A: hsp=Pρg=100kpa1000×9.81=10.19hs=3mhf=4mhvp=Pvρg=10kpa1000×9.81=1.019

Q: Proble discharge through the orifice is 0.85 litre/s. Find the co-efficient of discharge. The head…

A: Diameter of orifice = 20 mm = 0.02 m Head = 1 m Actual discharge = 0.85 lit/s

Q: Centrifugal pump is a kinetic device and uses the centrifugal force to push out the fluid. So the…

A: Centrifugal pumps works by  transferring the low viscosity fluids in high flow rates, within low…

Q: Velecity of(3amls) A(5 cm) clia im pinges Water Jet with asingle Vane moving in Same. on olivecation…

A: Given: The diameter of jet, d = 5 cm = 0.05 m The velocity of jet, V1 = 30 m/s The velocity of…

Q: For a hydroelectric plant, a hydraulic turbine-generator is installed at the site below the free…

A:

Q: According to Figure 1, information given de= 500mm, Ve= 7.0 m/s, h= 5.0 m and PB= 105 kPa.…

A: i. The pump head is 41.2 m. The discharge of water is 1.37 m3/s. The pump power is 555.5240 kW.…

Q: Water is supplied in a 2-in. dia. pipe at the rate of 2 cfs to a 10-hp, SO-percent efficient pump.…

A: The Answer is below

Q: The flow rate of the system is 1 cubic meter per second. Determine the major and minor losses of the…

A: The flow rate of the system, Q=1 m3/s=35.3147 ft3/s                                       1…

Q: I have a question from my fluid power enginneering class. The question was, standard hydraulic oil…

A: Given: Pressure at the pump outlet is 10 psi. Height of uphill is 100 ft. Flow rate is 10 gpm.

Q: The density of water is loon tkg/a? and the e elective bulk modlus (k) is that ombong Carries water…

A: Since you have asked multiple questions in a single request we would be answering only the first…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.