A) A DC series motor has armature resistance of 0.6 Q and series field resistance of 0.4 0. The speed of the motor is 300 rpm and draws a current of 15 A when supplying a certain load. Neglect rotational losses and assume that there is no external resistance connected to the armature circuit. Find the torque developed by this machine, if you know that the motor is a 220 V, 7 hp DC series motor.

A) A DC series motor has armature resistance of 0.6 Q and series field resistance of 0.4 0. The speed of the motor is 300 rpm and draws a current of 15 A when supplying a certain load. Neglect rotational losses and assume that there is no external resistance connected to the armature circuit. Find the torque developed by this machine, if you know that the motor is a 220 V, 7 hp DC series motor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 220 V DC series motor runs drawing a current of 30 A from the supply. Armature and field circuit resistances are 0.4 and 0.1 respectively. The load torque varies as the square of the speed. The flux in the motor may be taken as being proportional to the armature current. To reduce the speed of the motor by 50% the resistance in ohms that should be added in series with the armature is
A 250 V series motor has an armature resistance of 0.2 ohm and a series-fieldresistance of 0.18 ohm. If the speed is 6oo RPM when the current is 32 amps.What will be the motor speed when the load is reduced so that the current is18 amps, under which condition the percent flux change is 50 % of the percentcurrent change.
(7) The only parts suffers from eddy currents in AC motors: a- The stator. b- The rotor. c- The stator and rotor. (8) The unit of torque is a- W (rad. s') b- Js -1 C- Nm
A shunt dc motor has armature voltage = 150 V, armature field resistance = 100 2, and armature resistance = 1.6 Q. At a certain torque the motor rotates at 1350 R.P.M and takes a current = 12 A. what will be the load torque?
A 230 V dc series motor has an armature resistance of 0.2 ohm and field resistance of 0.1 ohm at rated voltage. The motor draws a line current of 40 amperes and runs at a speed of 1000 rpm. Find speed of the motor for line current of 20 A at 230 V. Assume that flux at 20 A line current is 60% of flux at 40 A line current.
Reducing the supply voltage so that Vnew = Vold / V3 reduces the maximum torque of the motor so that Tmaxnew= ...Tmaxold . * .... ...
16 A 4-pole dc series motor has wave connected winding with 600 conductors. When fed from 250 V dc source, the motor drives a load of 5 kW and takes 50 A with a flux per pole of 10 mWb. The torque developed is (Neglect losses).
2. A 2-pole, 50 Hz induction motor supplies 15 kW to a load at a speed of 2950 rpm. a. What is the motor's slip? b. What is the induced torque in the motor in N-m under these conditions? c. What will be the operating speed of the motor be if its torque is doubled? d. How much power will be supplied by the motor when the torque is doubled?
a 220 V dc shunt motor has armature resistance 0.23 ohm, on load it takes armature current 40 A and turnes at 720 rpm, if the flux of motor is reduced by 10% without changing the load torque . Find the new speed of the motor.
459. The current drawn by a 460 V dc motor of armature resistance 0.5 ohm and back emf 420 V is -
The flux in a 18 KW, 120 V, Duplex Lap-Wound DC machine has been set to induce rated voltage at a speed of 1500 RPM. This machine induces a torque of 88.65 N.m. under a certain load. Find the product Ko, and find the armature current under that load. Select one: O a. Product = 0.764, and Armature Current = 116 A O b. None O c. Product = 0.08, and Armature Current = 110.8 A O d. Not enough information is given to find the current
A DC series motor having a resistance of 0.4 o and runs at 2000 rpm when connected to 250 V supply and drawing a current of 2O A. (i) What resistance must be added in order to limit the speed to 4000 rpm when armature current is 5A? Assume flux varies linearly. (ii) What resistance must be added to limit the speed to 1000 rpm when armature current is 30 A? Assume that the flux at 30 A is 20% more than that at 20A. (iii) At what speed the motor will run if it is connected directly to 250 V supply when the load is such that the current drawn is 30 A? *