In a spinning industry, a 215 V, 4 pole shuntmotor runs at a speed of 1300 rpm gives anoutput of 8 HP with an armature current of 38A. The armature winding is wave-connectedand it has 670 conductors. Its armatureresistance is 0.5 N and drop at each brush is 1V. Find (i) Useful torque, (ii) Total torque, (iii)Useful flux per pole and (iv) Rotational lossesoccurring in the motor. [ 1HP= 746 W ]Useful TorqueTotal TorqueFlux per poleRotational Loss in the Motor

In this question we will find dc shunt motor torque , flux etc...

In a spinning industry, a 215 V, 4 pole shunt motor runs at a speed of 1300 rpm gives an output of 8 HP with an armature current of 38 A. The armature winding is wave-connected and it has 670 conductors. Its armature resistance is 0.5 Q and drop at each brush is 1 V. Find (i) Useful torque, (ii) Total torque, (iii) Useful flux per pole and (iv) Rotational losses occurring in the motor. [ 1HP= 746 W ] Useful Torque Total Torque Flux per pole

In a spinning industry, a 215 V, 4 pole shunt motor runs at a speed of 1300 rpm gives an output of 8 HP with an armature current of 38 A. The armature winding is wave-connected and it has 670 conductors. Its armature resistance is 0.5 Q and drop at each brush is 1 V. Find (i) Useful torque, (ii) Total torque, (iii) Useful flux per pole and (iv) Rotational losses occurring in the motor. [ 1HP= 746 W ] Useful Torque Total Torque Flux per pole

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: An eight-pole, 24 KW, 124 V, DC machine has a duplex LAP-wound armature which has 72 coils with 6…

A: No. Of poles, P = 8 No. Of parallel paths, A = 2*8 Conductors, Z = 72*6*2 Voltage, E = 124V Speed, N…

Q: Give the relevant details for drawing lap winding for a de machine with 4 poles, 22 slots and 6…

A: We need to give relevant details for drawing a lap winding for a dc machine having, Poles (P) = 4…

Q: 1.7)The armature of a 4-pole de machine rotates at 840 rpm .The armature length and diameter are 40…

A: The answer to the above problem is provided below. Hope it helps.

Q: A 24 KW, 140 V, Duplex Lap-Wound DC machine has been set to induce rated voltage at a constant K…

Q: an overall efficiency of 83.5%.

Q: DC series motor

A: For the DC series motor, Ise=Ia =Ia Flux, conductor, poles, armature resistance values given in…

Q: 4) A dc. ahunt machine while running as generator develops a voltage of 240 V at 1000 rp.m. on…

A: In this question we will find speed and efficiency of motor with given data....

Q: A 22 kW, 230 V Series DC motor runs at 750 rev/min at full load and draws 110 A from the supply. The…

Q: Q2: If the rated frequency for an induction motor is 60 Hz and the maximum tonque Tm is 100 N.m,…

Q: An eight-pole, 24 KW, 100 V, DC machine has a duplex LAP-wound armature which has 64 coils with 10…

Q: 16 A 4-pole dc series motor has wave connected winding with 600 conductors. When fed from 250 V dc…

A: In this question We need to determine the torque developed of the motor We know Torque = power/w…

Q: An eight-pole, 24 KW, 100 V, DC machine has a duplex LAP-wound armature which has 64 coils with 10…

Q: A 24 KW, 140 V, Duplex Lap-Wound DC machine has been set to induce rated voltage at a constant K…

Q: A 220 V DC series motor runs drawing a current of 30 A from the supply. Armature and field circuit…

A: It is given that:

Q: A dc generator has a prime mover that provides a speed of 1772 rpm at a torque of 24.4 N-m. With…

Q: (7) The only parts suffers from eddy currents in AC motors: a- The stator. b- The rotor. c- The…

A: 7. Answer: The stator and rotor Explanation: The rotating magnetic field and induced voltage cause…

Q: A four-pole, lap-would DC machine has 462 conductors in the armature. The average flux per pole is…

Q: Q.36 Name three factors that determine the torque produced by an induction motor. Select one or…

A: Those three factors are following in which torque depends upon:- i) the magnitude of rotor current.…

Q: armature winding of a 200-V, 4-pole, series motor is lap-connected. There are 280 slots and each…

A: We need to find out speed for given motor

Q: Q- The armature resistance of a permanent magnet dc motor is 0.80. At no load, the motor draws 1.5 A…

Q: A 24 KW, 140 V, Duplex Lap-Wound DC machine has been set to induce rated voltage at a constant K…

Q: The flux o in a 16 KW, 100 V, Duplex Lap-Wound DC machine has been set to induce rated voltage at a…

A: Given Power,p = 16 KW, Voltage,V = 100 V, Duplex Lap-Wound DC machine has been set to induce rated…

Q: Q- The armature resistance of a permanent magnet dc motor is 0.80. At no load, the motor draws 1.5 A…

A: Given- Armature resistance- Ra=0.8 Ω, Current- Ia=3.5 A, supply voltage V=25 V, speed=1500 RPM, To…

Q: Justify why an electrostatic motor cannot be operated from dc supply. Derive the expression of…

Q: A dc shunt motor runs at 900 rpm from a 460 V supply when taking an armature current of 25 A.…

Q: The induced torque in induction machines depends on Select one: Oa The slip Ob. The mechanical speed…

A: The explanation is as follows.

Concept explainers

Winding and Constructions

Alternating Current (AC) winding is generally of the 3-phase type due to the inherent advantages of the 3-phase machine. Armature coils must be connected to the yield balance (equivalent in magnitude and 2/3 of the series phase difference of the rod) 3-phase electromotive forces (emf). The armature should be divided into step-bands to start with slots around the perimeter.In the construction of AC machines, the frame is used as an external protective shield to protect it from environmental conditions. The frame also serves as the outer perimeter, allowing the interior to be easily placed. The static state section of the devices is the stator winding attached stator.

Question

In a spinning industry, a 215 V, 4 pole shunt
motor runs at a speed of 1300 rpm gives an
output of 8 HP with an armature current of 38
A. The armature winding is wave-connected
and it has 670 conductors. Its armature
resistance is 0.5 N and drop at each brush is 1
V. Find (i) Useful torque, (ii) Total torque, (iii)
Useful flux per pole and (iv) Rotational losses
occurring in the motor. [ 1HP= 746 W ]
Useful Torque
Total Torque
Flux per pole
Rotational Loss in the Motor

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Winding and Construction of the Rotor and Stator

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Electrical machines
A direct current shunt dynamo continuously supplies an ohmic load of 50 Ohm at terminal voltage Vt= 1000 V. The armature winding resistance is 5 Ohm and the shunt pole winding resistance is 200 Ohm. The sum of mechanical losses is 400 W. What is the percent efficiency of the dynamo under these operating conditions? a) 70 b) 74 c) 87 d) 78 e) 85
A DC motor with a shunt field winding has the following characteristics: Vr = 96.0 V R = 1.50 Q K = 0.352 m Specify the flux required to achieve a starting torque of 18 Nm.
Stray losses represent: O A. Resistive losses in the windings of the machine O B. Losses due to friction of the moving parts O C. Losses due to magnetization and demagnetization of the core O D. Windage losses O E. None of the other choices are correct
An eight-pole, 24 KW, 124 V, DC machine has a duplex LAP-wound armature which has 72 coils with 6 turns per coil. Its rated speed is 3000 RPM. Ass ume no dead zone Find the constant K and the flux per poleto produce 80 Volts at no-load conditions Select one: O a. None O b. K = 68.86 and flux = 3.33 mwb/pole O c. K = 68.755 and flux = 3.7 mWb/ pole O d. K = 95.5 and flux = 3.7 mWb/ pole
This course O d. None The flux o in a 18 KW, 120 V, Duplex Lap-Wound DC machine has been set to induce rated voltage at a speed of 1500 RPM. Find the product Ko, and find the induced torque in this machine at no load. Select one: O a. Product = 0,764, and Induced Torque = 114.6 N.m. O b. None Oc. Product = 0.764, and Induced Torque = 0 N.m O d. Not enough information is given to find the torque INEXT Dur
This course EHide blom Clear my choice An eight-pole, 24 KW, 124 V, DC machine has a duplex LAP-wound armature which has 72 coils with 6 turns per coil. Its rated speed is 3000 RPM. Assume no dead zone Find the constant K and the flux per pole to produce 80 Volts at no-load conditions Select one: a. None Ob. K = 68.86 and flux = 3.33 mWb/pole Oc.K = 68.755 and flux = 3.7 mWb / pole O d. K = 95.5 and flux = 3.7 mWb / pole A peries DC motor has a series-field windino of 25 turns per pole. Its armature resistance in 0,1 2. and its
A DC series motor having a resistance of 0.4 ꭥ and runs at 2000 rpm when connected to 250 V supply and drawing a current of 20 A. (i) What resistance must be added in order to limit the speed to 4000 rpm when armature current is 5A? Assume flux varies linearly. (ii) What resistance must be added to limit the speed to 1000 rpm when armature current is 30 A? Assume that the flux at 30 A is 20% more than that at 20A. (iii) At what speed the motor will run if it is connected directly to 250 V supply when the load is such that the current drawn is 30 A?