(a) A 0.9 m diameter backward curved centrifugal fan is supplying 4 m3/s at 325 Pa, 1000 rpm and 1750 W. A fan geometrically similar to this fan must operate at 425 Pa and 1 m³/s. Determine the wheel diameter, speed and power required. [0.42 m, 2446 rpm, 567 W] (b) The fan in (a) supplies 3 m³/s at 1000 rpm. The system is altered so that the resistance is less and delivers 4 m³/s. Determine the speed at which the fan must operate to supply exactly 3 m³/s and the static pressure of that fan. [750 rpm, 182.81 kPa]

(a) A 0.9 m diameter backward curved centrifugal fan is supplying 4 m3/s at 325 Pa, 1000 rpm and 1750 W. A fan geometrically similar to this fan must operate at 425 Pa and 1 m³/s. Determine the wheel diameter, speed and power required. [0.42 m, 2446 rpm, 567 W] (b) The fan in (a) supplies 3 m³/s at 1000 rpm. The system is altered so that the resistance is less and delivers 4 m³/s. Determine the speed at which the fan must operate to supply exactly 3 m³/s and the static pressure of that fan. [750 rpm, 182.81 kPa]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a 6.25-inch Model 4075 pump operated at 1160 rpm, if 450 GPM of water is to be delivered, what will be the estimated pump head in ft? HEAD IN FEET 30 25 0 0 0 10 O 6 ft 7.25" (184mm) 20 7.00" (178mm). 6.75" (171mm). 6.50" (165mm)] 15 6.25" (159mm). 5 O 16 ft O 20 ft O 12 ft aco® L/SEC 5 OT 10 Model 4075 FI & CI Series 15 -6-6 ⁰ dº 20 ANA 888 778 25 REQUIRED NPSH do 1160 RPM November 1, 2010 K ・dº- [M 90 do 30 8800 81 1HP(.75KW) DeJ kin do 60% 35 do 50 Curve no. 2175 Min. Imp. Dia. 6.25" Size 5 x 4 x 7.0 40 45 3HP(2.2KW), 2HP(1 5KW) 5HP(1 1KW)> CURVES BASED ON CLEAR WATER WITH SPECIFIC GRAVITY OF 1.0 L 75 150 225 300 375 450 525 600 675 FLOW IN GALLONS PER MINUTE NOWONG FEET 15 12 7 6 2 1 NPSH 758 50 5 HEAD IN METERS 45 586888 KPO 60 40 20 10 LO HEAD IN KILOPASCALS
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
Hydrodynamics pumps 5. A centrifugal pump has r1 = 6 in., r2 = 12 in., b1 = 3 in., b2 = 2 in., β1 = 20°, β2 = 10° and rotates at 1200 rev/min. If the fluid is water at 60°F, estimate the theoretical (a) flow rate, in gpm; (b) the head in ft; and ( c) the water horsepower, HP. Assume near-radial entry flow. a. flow rate Answer : ____________________ gpmb. head Answer : ____________________ ftc. water horsepower Answer : ____________________ HP
Using data given below, determine the main dimensions and blade angles of a Francis turbine. Net head=65 m, speed= 700 rpm, BHP= 400. Actual hydraulic efficiency3D 94%, overall efficiency= 85%, flow ratio= 0.18, wheel width at inlet/ wheel diameter at inlet=0.1, inner diameter/ outer diameter= 0.5. Assuming constant velocity of flow and radial discharge. Neglect area blocked by blades. Vane angle at inlet: 27° 39 33° 53 41° 82 O 52° 56
i need ans very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
A turbine has the following data: inlet radius = 2.2 m outlet radius = 1.5 m blade width at inlet = 0.8 m blade width at outlet = 2.1 m inlet blade angle = 66º outlet blade angle =18.5ºN = 100 rpm Q = 85 m3/s Calculate the angle at the inlet by which the wicket gates should turn the flow from radial. Round off your final answer to two decimal places.
Hydro electric station is installed to utilise 30 ma/sec of water of a river at a head of 7.5 m. If 85% turbine efficiency can be counted on, (i) is it feasible to develop this power by two turbines with rpm not less than 50, the turbine having specific speed not greater than 540 rpm ? (ii) what type of runner will be used ? (iii) what is the diameter of runner if the speed ratio is 0.85? [(i) N = 156'5 rpm, .. yes (ii) Kaplan (iii) P25 m]
7.8 A turboblower develops 750 mm W.G. at a speed of 1480 rpm and a flow rate of 38 m³/s. It is desired to build a small model which develops the same head at a higher speed (2940 rpm) and low discharge. Determine the specific speed and the flow rate through the model.
Using data given below, determine the main dimensions and blade angles of a Francis turbine. Net head=65 m, speed%3 700 rpm, BHP= 400. Actual hydraulic efficiency= 94%, overall efficiency= 85%, flow ratio= 0.18, wheel width at inlet/ wheel diameter at inlet=0.1, inner diameter/ outer diameter= 0.5. Assuming constant velocity of flow and radial discharge. Neglect area blocked by blades. Vane angle at inlet:
12- The Pelton wheel shown in Fig. is being driven at 200 rpm by a 45 m/s jet of water. The jet diameter is 6 cm. Determine the power developed by the wheel? [Ans. Power 124.65 kW] 1.2 m