A centrifugal pump impeller has an external diameter of 1.2 m and internal diameter of 0.8 m. The width of the impeller at outlet is 0.175 m and the blade angle at outlet is 65 degrees. The flow velocities at inlet and outlet are the same (Va1 = Va2). This pump delivers 1.55 m3/s of water at 210 rpm. For theoretical performance, calculate:

A centrifugal pump impeller has an external diameter of 1.2 m and internal diameter of 0.8 m. The width of the impeller at outlet is 0.175 m and the blade angle at outlet is 65 degrees. The flow velocities at inlet and outlet are the same (Va1 = Va2). This pump delivers 1.55 m3/s of water at 210 rpm. For theoretical performance, calculate:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A single stage centrifugal pump has an impeller of 250 mm diameter which rotates at 1,800 rpm and lifts 60 lit/sec to 25 m with an efficiency of 70%. Obtain the number of stages and diameter of each impeller of a similar multi-stage pump to lift 75 lit/sec to 175 m at 1,500 rpm. (8 stages ; 280 mm dia)
This course EHide block A centrifugal pump with the following impeller dimensions is used to pump water. The pump is running at 1000 rpm. The ideal head rise through the pump is 190 ft. b2 Poz 72 by The parameters of the impeller are as follows: r2= 9in, b2=3in, B2= 31° Take g= 9.81 m/s23 32.2 ft/s2 pw = 998 kg/m3 = 1.94 Slug/ft. Determine the theoretical flow rate in gpm Choose.. Determine the theoretical Power shaft in (hP) Choose...
4. A centrifugal pump delivers water to a height of 22 metres at a speed of 800 r.p.m. The velocity of flow is constant at a speed of 2-0 m/s and the outlet vane anglc is 45°. If the pump discharges 225 litres of water per second, find the diameter of the impeller and width of the impcller at oudet. (Ans. 375 mm: 95 mm)
- A centrifugal pump with an impeller diameter of 350mm and specific speed of 19.15 and requires 15 kW to discharge 2.4 m³ /min of water, and runs at 1800 rpm. Determine the discharge, head and power required when the pump runs at 2400 rpm. The same discharge could be obtained by altering the impeller diameter without changing the rotational speed for this case find the new diameter of the impeller the head and the power required.
The external and internal diameters of the impeller of a centrifugal pump are 0.3 m and 0.15 m respectively. The rotational speed of the pump is 1200 rpm and the vanes make an angle of 28° with the peripheral velocity direction at the outlet. The velocity of the flow through the impeller is constant at 1.7 m/s. Assuming the manometric efficiency of 82%, find the vane angle at the inlet (°). 18:19 /
A Centrifugal pump is to discharge water at the rate of 110 lits/sec at the speed of 1450 rpm agalnst head of 13 m. Impeller diameter is 250 mm and its width is 50 mm. If manometric efficiency is 75%, determine vane angle at outer periphery.
Water at 20"C Bows through the pump impeller shown in the figure below, where the inner and outer diameters of the impeller are 160 mm and 400 mm respectively, and the width of the pump blades is 55 mm Part A Wan- μA Estimate the shaft power required to drive the pump at this operating condition Express your answer to three significant figures and include appropriate units. Value Blade Pump impeller The impeller rotates at 3600 rpm Under a particular operating condition, water enters in a direction normal to the inflow surface, the component of the outflow velocity normal to the outflow surface. V is equal to 17 m/s, and the magnitude of the absolute velocity, V, at the outflow surface is 33 m/s Submit Request Answer Units Outflow surface Inflow surface ? 160 บท 400 mun
Figure below shows the performance curve family of Model 5009 Centrifugal pumps of Taco Pump Inc., running at a fixed speed of N = 1160 rpm. For the pump with the impeller diameter D = 8.625 in., calculate the power coefficient (Cp*) of the given pump at BEP if water is the fluid. HEAD IN FEET 0000 50 40 20 10 8.625" 30 (219mm). 0 O 0.821 O 0.731 O 0.467 aco 10 O 0.235 L/SEC 5 9.25" (235mm) 8.00" (203mm) 7.375" (187mm) 6.75" (171mm) 125 Model 5009 FI & CI Series 25 15 20 -do CURVES BASED ON CLEAR WATER WITH SPECIFIC GRAVITY OF 1.0 72% 75% 30 79% 1160 RPM FEBRUARY 19. 2002 40 3,5 45 REQUIRED NPSH 1.5HP (1.1KW) 79% 1⁰⁰ of 15² Curve no. 2140 Min. Imp. Dia. 6.75" Size 6 x 5 x 9.0 50 55 60 250 375 500 625 FLOW IN GALLONS PER MINUTE 72% 2HP(1.5KW) colo & 2⁰. It & SC- 09. 55% 5% 3HP (2.2KW) 7.5HP(5.6KW) 45% de 750 875 NGFEET 15 12 -9 -6 3 0 10 8 50 SHP(3.7KW) NPSH HEAD IN METERS 1000 r45 36 F27 18 -9 0 -100 --80 4 -40 -60 2 -20 -O HEAD IN KILOPASCALS
A double acting reciprocating pump running at 40 rpm is discharging 1.0 m3/ minute. The pump has a stroke of 400 mm. The diameter of the piston is 200 mm. The delivery and suction heads are 20m and 5m respectively. Find the slip of the pump and power required to drive the pump.
A centrifugal pump having an impeller of diameter 500 mm delivers 140 litres of water per sccond. The velocity of flow is 1 m/s and the vanes are curved back at outlet at 30° to the wheel tangent. If the impeller speed is 400 r.p.m., find the power to drive the pump. (Ans. 12-9 kW) 3.
The impeller of a centrifugal pump is 0.5 m in diameter and rotates at 1200 r .p. m . ; blades are curved back to an angle of 30⁰ to the tangent at outlet tip . If the measured velocity of flow at outlet is 5 m/ sec. If the pump is provided with whirlpool chamber which reduces the velocity of water by 50%. Kinetic energy converted into in whirlpool chamber in j/kg/sec And tangential velocity of runner at outlet
It is desired to deliver 4 gpm at a head of 670 m in a single pump having specific speed not to exceed 40. If the operating speed is not to exceed 1352 rpm, how many stages are required? Select the correct response: 0 7 O 5 3 6 Contin 2.