A 9-kg block is suspended from a spring having a stiffness of k = 200 N/m. If the block is given an upward velocity of 0.4 m/s when it is 95 mm above its equilibrium position, determine the maximum upward displacement of the block measured from the equilibrium position. Assume that positive displacement is downward.

Q: 7.15 Two left-hand helical gears having the same helix angle are used to connect two shafts 60°…

A: (a) The number of teeth on gear: ZG = 62 teeth (b) The number of teeth on pinion: ZP = 25 teeth

Q: A person with a body mass of m= 99 kg and height h = 1.74 m stands with their arms straight out.

A: Mass, m=99 kg,Height, h =1.74 m,

Q: 4/16 The rectangular frame is composed of four perim- eter two-force members and two cables AC and…

A:

Q: Find the value of stress Force 2.2 N Area=2 m2

A:

Q: Q6) For the presented figure: a-What is the accuracy of the vernier caliper. b- What is the value of…

A: A vernier calliper is used for the measurement of the length to an accuracy of 10-4 m. The vernier…

Q: What size of new cast iron pipe (roughness of 0.00026) is needed. to transport 550 L/s of water for…

A: Given data as per the question Q=550 =0.550 m3s Length of pipe =1 km =1000 mhead loss =3m

Q: When a 2-kg block is suspended from a spring, the spring is stretched a distance of 40 mm. Determine…

A:

Q: the net heat input

A: Given data;  Current=250 A Voltage,v= 20 V Welding speed,=5 mm/s Arc efficiency=70%=0.7Determine the…

Q: When the pressure on a given mass of liquid is increased from 3.0 MPa to 3.5 MPa, the density of the…

A: As given in question, Initial pressure = P = 3 MPa Final pressure = P' = 3.5 MPa Initial density = ρ…

Q: the net heat input per unit length of the weld.

A: Given data;  A gas tungsten arc welding operation is performed using;  current,c= 300 A  Voltage,v=…

Q: What are the physical and thermal properties of water at 6 degrees celsi

A:

Q: In an ideal Rankine cycle, steam is generated at 4.1 MPa and 480°C. The condenser is at 32°C.…

A:

Q: 4- The cross-section of the ABCD element in the figure is a circle with a diameter of 6 cm. The…

A:

Q: 4. Consider the right-handed coordinate system below. The force F = 800 N has its line of action…

A:

Q: Find hydraulic radius Wetted area=5 m2 Wetted perimeter-7

A:

Q: A continuous and aligned fiber-reinforced composite is to be produced consisting of 30% vol aramid…

A: Write the give data. Ef=121.68 GPaVf=0.30Em=3.42 GPaVm=0.70

Q: Write down the derivation of formulas and describe each variable for Work and Energy.

A:

Q: 1- The effective porosity is the value that is used in a gas reservoir engineering calculations.

A: Disclaimer: “Since you have asked multiple questions, we will solve the first question for you. If…

Q: Find and solve at least 10 problems (5 easy and 5 hard) for Work and Energy

A: Given Work and energy To find 10 problems

Q: II. Solve the problems below: 1. A rigid bar, pinned at O, is supported by a steel spring at A and a…

A: Answer: (a) The shearing stress in steel spring is 2.87 MPa. (b) The shearing stress in bronze…

Q: Calculate the critical radius of insulation for asbestos (k=0.17 W/m.C) surrounding a pipe and…

A: Thermal conductivity of asbestos, k=0.17 W/m.CRoom air temperature, Ta=17oCHeat transfer…

Q: QUESTION 7 A pump discharges water at 4 m³/s through a pipe. If the pressure difference between the…

A: FOLLOWING IS THE SOLUTION

Q: the net heat input per unit length of the weld.

A: Given data;  Arc efficiency,η=80 %=0.8Current,c=700 Avoltage,v=30 VWelding speed for the weld is=10…

Q: Find potential energy

A: Given data : Mass=m Acceleration due to gravity=g Height=h   Required : Potential energy

Q: A particle which moves with curvilinear motion has coordinates in millimeters which vary with the…

A: Velocity of a moving body is defined as the rate of change of position with respect to time in a…

Q: Q2(30%) Determine the resultant of forces system shown in Figure and locate it with respec point C?…

A: Given   Force, F1 = 380 kN             F2 = 20 kN             F3 = 30 kN             F4 = 80 kN Find…

Q: A supersonic wind tunnel is in the design

A: given P0=6*105PaT0=313 KA1=1.2 m2M1=3.5 AA*=1M2γ+11+γ-12M2.5γ+1γ-1

Q: A Kaplan turbine works under a head of 10 m. The design speed is 50 rpm and turbine develops 40000…

A: We know that a Kaplan turbine can operate at a head of 10 metres.The turbine has a design speed of…

Q: 6/15 The uniform slender bar has an ideal roller at its upper end A. If the coefficient of static…

A:

Q: the net heat input per unit length of the weld.

A: Given data;  A gas tungsten arc welding operation is performed usingcurrent=650 A, voltage=10 V…

Q: The mass of block B is 95kg while that of A is 59kg. A horizontal force P=468N is applied at block…

A:

Q: A car travelling at a horizontal path (starting from rest) encounter a resistance four times its…

A:

Q: A 75-mm diameter orifice discharges 23.41 L/s of liquid under a head of 2.85 m. The diameter of the…

A:

Q: Two pumps (Pump A and B) have performance curves which can be approximated by the following…

A: HA= 340 - 1.2Q2HB= 360 - 2.5Q2

Q: Compute for the moments of inertia and radius of gyration of the shaded area with respect to the x -…

A: Now first of all we need to separate the shapes

Q: 1. Why is it important to follow the instruction on the books especially the recommended welding…

A:

Q: Regarding amorphous plastics, explain why they tend to have higher tensile strength when deformed…

A: INTRODUCTION: Amorphous materials are found in both natural and manufactured systems. Thin-film…

Q: An aluminum alloy [E = 10,000 ksi; ay = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi;…

A:

Q: A potential flow model of flow over a circular cylinder is described by the following velocity…

A: Write the expression of velocity potential. ϕ=U∞cosθr+R2r2 Calculate the velocity components.…

Q: Expound on twinning as a mechanism for plastic deformation and include conditions for which it will…

A: Twining is the mechanics of plastic deformation in metallic materials. It is a shear force that can…

Q: 6. Marbles having a mass of 5 g fall from rest at A through the glass tube and accumulate in the can…

A:

Q: the net heat input per unit length of the weld.

A: Given data;  Gas tungsten arc welding operation is performed using Voltage=30 V Current=520 A…

Q: A 150 MW power plant using a regenerative cycle is utilizing steam at 5 MPa, 510°C. The open heater…

A: Answer: ◆ The % mass extracted for the 1 MPa open heater is: 9.646%◆ The % mass extracted for the 3…

Q: 6/20 The force P is applied to (a) the 60-lb block and (b) the 100-lb block. For each case,…

A:

Q: Two parallel planes (90 by 60 cm) are separated by a distance of (60 cm). One plane is maintained at…

A:

Q: Compound axial member ABC has a uniform diameter of d = 2.9 in. Segment (1) is an aluminum [E₁ =…

A: INTRODUCTION: A composite bar is constructed of two bars of different materials that are firmly…

Q: 5-An 80-L rigid tank contains an ideal gas mixture of 5 g of N₂ and 5 g of CO₂ at a specified…

A: INTRODUCTION: In this problem, we will determine the dinitrogen's distinct volume. To determine the…

Q: Q2/A vertical cylinder having a length of 30 cm is maintained at 100-C and exposed to room air at…

A:

Q: Petermine the displacement W= 0-589 J F = 0-3 N

A: Given data : Force=F Work done=W   Required : Displacement

Q: A cylinder (diameter 4 m) of weight 50 kN is placed on the bottom of the tank as shown and oil and…

A: Given data Diameter of cylinder = 4 m Weight = 50 kNAssuming length of cylinder = 1 mWe have to find…

Forced undamped vibrations

In mechanical engineering, vibration is expressed as the term that occurs due to an object's backward and forward movement about a point of equilibrium. Generally, there are three types of vibrations which are,