A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolute pressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa?

A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolute pressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. 1.5 m Determine the resultant force the oil exerts on the semicircular surface AB. The tank has a width of 3 m. Take Poiu = 900 K9/. m3 0.5 m (50.132 kN) 1 m 1m
An upward flow of oil (mass density 800 kg/m³, dynamic viscosity (0.8 kg/m-s) takes place under laminar conditions in an inclined pipe of 0.1m diameter as shown in the figure. The pressures at sections 1 and 2 are = 200 kN/m². measured as p₁ = 435 kN/m² and P₂ 2- 45° 5m F5 The discharge in the pipe is equal to
Problem P68 (a) Determine the magnitude of the anchoring force needed to hold the horizontal bend and nozzle in place. The velocity at location 1 is known to be 2 m/s. The pressure at location 1 of the 300 mm diameter pipe is known to be 100 kPa. The discharge at section 2 is in the form of a free jet to the atmosphere. Ans: F = 8.345 kN 300 mm 160 mm Diameter Jet P₁ = 100 KPa Reducing Bend with Nozzle FRB/F
An open cylindrical tank contains water 1.25m. If the cylinder rotates about its geometric axis with angular velocity 90 r.p.m, find the diameter and original depth of the tank. If the pressure at the edge of the cylinder is 15 kPa.
Water flows at 2 m / s in a 3 m wide 2.5 m deep rectangular channel. There is a 1.10 m elevation on the downstream side of the channel as seen in the figure. Above the elevation, the channel widens to 3.75 m as shown in the figure If b2 = 3.75 m, what should be the maximum value of Δz to prevent suffocation? Draw the specific energy depth curve.
A viscous liquid (p = 1.2x10°kg/m³, µ = 0.0048 Pa.s) flows at a rate of 10ml/s through a horizontal, 4 mm diameter tube. The pressure drop along a 1 m length of the tube which is far from the tube entrance so that the flow is fully developed is _(kPa)
An orifice having an area of 0.0003 m2 is located on the vertical side of a tank. The tank has a constant cross-sectional area of 0.40 m2. It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Determine the following:a. Coefficient of dischargeb. The time to lower the head from 1.20 m to 0.80 m when C = 0.60.c. The head after 240 seconds from an initial head of 1.20 m when C = 0.60
The value of Ca varies from 0.61 to 0.65. For general purpose the value of Ca is taken as 0.62. Problem 7.1 The head of water over an orifice of diameter 40 mm is 10 m. Find the actual dis- charge and actual velocity of the jet at vena-contracta. Take Cd = 0.6 and C,, = 0.98.
A 50 mm diameter siphon discharges water from a reservoir (Point 1 elev = 20m) into open air (Point 3 elev. 10m). The head loss from the reservoir (point 1) to the summit (point 2 elev = 28m) is 3 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. Determine the velocity in the siphon in m/s? 3 The correct answer has a margin of 0.05 from the exact answer. TOCUL T OWCT. 7:13 PM 27°C Rain showers 入口の ENG 04/10/2021