Answered: 150 mm diameter, having a coefficient…

150 mm diameter, having a coefficient of contraction of 0.65 discharges oil (SG=0.80) under a head of 8m. The average actual velocity of the jet is 11.65 m/s. Compute the head loss of the orifice.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. The head of water over an orifice of diameter 100 mm is 8 m. Using C = 0.63 and Cv = 0.98, find…

Q: A small orifice in area is in the vertical side of a rectangular tank. The horizontal sectional area…

Q: A right circular tank 6 m. in diameter and 12 m. high is filled with 6 m. of oil sp. gr. = 0.80 and…

A: Diameter of tank = 6 m Initial Height of fluid = 12 m Diameter of orifice = 75 mm

Q: a. Determine the average cross-sectional velocity V and the discharge Q for the compound channel…

A: Given :

Q: D A cylindrical tank with its axis vertical gas a diameter of 2 m and a depth of 8 m. A standard…

Q: 2. Given H = 1.8 m & D = 0.2 m through the hole in the open top container. Determine the head losses…

Q: A cylindrical tank having a diam. of 4 m/s and 8 m is full of water. There is an orifice at the…

Q: The actual velocity in the contracted section of a jet of liquid issuing from a 5 cm diameter…

A: 1. Diameter of the orifice = 5 cm2. Actual velocity in the contracted section = 7.5 m/s3. Head…

Q: 3. Find the discharge through a totally drowned orifice 3 m wide and 1 m deep, if the difference in…

Q: A rectangular tank 3.6 m long and 1.8 m wide is divided into two parts, by a vertical dividing plate…

A: Volume of water required to be removed= 3.6*1.8*0.9*0.66= 3.84912 m3. Area of cross section of…

Q: Q.2.8 MASS FLOW AT A PIPE JUNCTION Consider the s. v low in a water pipe joint shown in the diagram.…

Q: A sharp-edged orifice 100 mm in diameter, in the side of tank having a horizontal cross-section 2 m…

A: do = 100mm or 0.1mD = 2m Q1 = 20 L/s or 0.02 m3/s Q2 = 30 L/s or 0.03 m3/s Cd = 0.60 -

Q: The diameter of a pipeline at point 1 is 75 mm and at point 2 is 25 mm. Points 1 and 2 are at the…

A: Consider the following figure. The specific gravity is G=1.4. The pressure head at point 1 is,…

Q: A 75 mm diameter orifice discharges 0.023 m/s of liquid under a head of 2.90 m. The diameter of the…

Q: An orifice is attached to a vertical side of a cylindrical tank having a diameter of 4m. The weight…

A: Given:- Diameter of tank=4 mDiameter of orifice=90 mmWeight of water discharged=22563 N in time of 1…

Q: A conical funnel has radius 4 cm and height 8 cm. A liquid is draining from the funnel at a constant…

A: Draining rate (Q) = 1.3 cm3/sRadius of cone (R) = 4 cmHeight of cone (H) = 8 cm(a) Depth of the…

Q: A 72 mm diameter orifice discharges 0.023 m3/s of liquid under a head of 3 m. The diameter of the…

A: Calculate coefficient of discharge,Cd

Q: 64 A pelton wheel works under a head of 400 m. Frictional loss through the pipe flow is limited to…

A: A Pelton wheel turbine-Head of wheel = 400 mLimitation of frictional loss = 10%The coefficient of…

Q: 4. A 10 cm diameter pipe has a discharge of 500 Vs. At a section, the pipe has sudden expansion to a…

Q: Calculate the discharge through the orifice.

Q: 1m V₁=0.5 m/s 20m 3m V₂=1.5 m/s 4m V3=0.3 m/s -22m a. Determine the average cross-sectional velocity…

Q: The diameter of a pipeline at point 1 is 75 mm and at point 2 is 25 mm. Points 1 and 2 are at the…

A: Given: The diameter of the pipe at point 1 is 75 mm. The diameter of the pipe at point 2 is 25 mm.…

Q: The volumetric flow through the pump in the figure is Q = 0.014 m3 / s. The fluid being pumped is…

Q: circular orifice of 50 mm diameter is fixed to the end of a water pipe of 75 mm diameter. The gauge…

Q: An orifice 150 mm diameter, having a coefficient of contraction of 0.65 discharges oil (SG=D0.80)…

A: The correct answer is 0.93

Q: 0.1.15. MASS FLOW AT A PIPE JUNCTION Consider the steady flow in a water pipe joint shown in the…

Q: 5. A right circular tank 6 m in diameter and 12 high is filled with 6 m of oil sg = 0.88 and 6 m of…

A: Diameter of tank = 6 m Initial Height of fluid = 12 m Diameter of orifice = 75 mm

Q: Discharge from an orifice of 75 mm diameter is 0.02 m³/s under a consta xternal mouthpiece of the…

Q: - The head in a vessel with vertical sides and a height of 4m at the instant of pening an orifice…

Q: Q.13.18 MASS FLOW AT A PIPE JUNCTION Cousuier the steady flow in a water pipe joint shown in the…

Q: A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev.…

Q: 4. Water flows through a horizontal nozzle, as shown. At the nozzle inlet the diameter is 6in. At…

A: Given- Diameter at inlet is d=6inDiameter at outlet is d=2in

Q: A prismatic vessel has two compartments A and B communicating by an orifice 0.3m square with C =…

A: Given data : C=0.60 orifice (b) = 0.3 m from diagram ; H=3m

Q: A closed cylindrical tank 3m high and 1m in diameter contains 1.2m of oil (SG = 0.8), 1m of water…

Q: 1. A circular orifice 30 mm in diameter, in the interval side of a vessel, discharge water under a…

Q: A 75 mm diameter orifice discharges 0.023 m3/s of liquid under a head of 2.90 m. The diameter of the…

Q: a siphon with its upper end immersed in a large reservoir of oil (s.g. 0.80). The pipe is 6 in in…

A: Answer we are given specific gravity of oil = 0.8 pipe diameter = 6 in head loss from 1 to 2 = 5…

Q: 2. Given H = 1.8 m & D = 0.2 m through the hole in the open top container. Determine the head losses…

A: GIVEN :- Head , H = 1.8 m Diameter of hole, D = 0.2 m Exit discharge, Q = 0.163 m3/s To Determine :-…

Question

An orifice 150 mm diameter, having a coefficient of contraction of 0.65 discharges oil (SG=0.80) under a head of 8m. The average actual velocity of the jet is 11.65 m/s. Compute the head loss of the orifice.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution:-

VIEW

Step 2 Solution:-

VIEW

Step 3 Answer:-

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Problem P68 (a) Determine the magnitude of the anchoring force needed to hold the horizontal bend and nozzle in place. The velocity at location 1 is known to be 2 m/s. The pressure at location 1 of the 300 mm diameter pipe is known to be 100 kPa. The discharge at section 2 is in the form of a free jet to the atmosphere. Ans: F = 8.345 kN 300 mm 160 mm Diameter Jet P₁ = 100 KPa Reducing Bend with Nozzle FRB/F
A 76-mm diameter orifice discharges 0.022 m3/s of liquid under a head of 3.5. The diameter of the jet at the vena çontracta is found by calipering to be 64 mm. Calculate the coefficient of discharge, Cd.
Include proper explanation this is fluid mech problem
Within 5 minutes
Fast
Do it
What is the velocity t the summit
In a nozzle shown in the figure, the fluid is Gasoline (p = 719 kg/m3, 9 = 4.06 x 10-7m²/s, P=2500 Pa, e=0.5mm and Q= 0.1 m3/s). Find the diameter of the pipe? %3D Elev, =82.65m . Elev. 66.66m 965.5m Lec. Sumayah Amal al-din Majeed
An orifice having an area of 0.0003 m2 is located on the vertical side of a tank. The tank has a constant cross-sectional area of 0.40 m2. It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Determine the following:a. Coefficient of dischargeb. The time to lower the head from 1.20 m to 0.80 m when C = 0.60.c. The head after 240 seconds from an initial head of 1.20 m when C = 0.60