A 5-kg homogeneous disk with a radius of 0.2 m is connected to a spring (k=50 N/m) as shown. At the instant shown (position 1), the spring is undeformed. The disk is released fr 25-degree incline. A clockwise constant 2 N-m couple is applied to the disk as it rolls down the inclined surface. Note: I disk = mR² 2 N-m 5-kg 50 N/m 000000000 1. Which of the following forces does negative work on the system? Friction between the disk and the inclined surface + x Mark 0.00 out of 20.00 2. Which of the following best approximates the magnitude of the work done by the spring?

A 5-kg homogeneous disk with a radius of 0.2 m is connected to a spring (k=50 N/m) as shown. At the instant shown (position 1), the spring is undeformed. The disk is released fr 25-degree incline. A clockwise constant 2 N-m couple is applied to the disk as it rolls down the inclined surface. Note: I disk = mR² 2 N-m 5-kg 50 N/m 000000000 1. Which of the following forces does negative work on the system? Friction between the disk and the inclined surface + x Mark 0.00 out of 20.00 2. Which of the following best approximates the magnitude of the work done by the spring?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 20kg slender rod AB is pinned to a roller at A that slides freely along the slot as shown in the figure below. The rod is released from the rest at an angle of 30. At the same time, a couple moment of M = 5 N.m in clockwise direction is applied at its centre of gravity. If immediately after the release the acceleration of the roller at A is 43m/s, determine the reaction forces at the pin connection at Point A.
Your answer is partially correct. The figure shows the cross section of a uniform 174-lb ventilator door hinged about its upper horizontal edge at O. The door is controlled by the spring-loaded cable which passes over the small pulley at A. The spring has a stiffness of 12.7 lb per foot of stretch and is undeformed when = 0. If the door is released from rest in the horizontal position, determine the maximum angular velocity reached by the door and the corresponding angle 0. Answer: Wmax = www 4.2' 0.636 rad/sec at 0 = 58.49 O
2. Consider the 5-1lb bar with length of 2½ feet and width of 2 inches. Small frictionless bearings are mounted to the ends, constraining the motion of the bar to the horizontal x and y slots. The bar starts at rest at positioned at 0= 45°. If an angular acceleration of 3 rad/s² is desired, what moment M must be applied to the bar? What are the reaction forces at A and B at that instant? Additional question: Does the width of the bar matter, or is it appropriate to consider the bar as a slender rod? Consider errors of less than 2% negligible.
The 10-kg wheel is rolling under the constant moment of M = 97 N-m. The wheel has radius r= 0.59 m, has mass center at point G, and the radius of gyration is kg = 0.27 m. The coefficients of friction between the wheel and the ground is ls = 0.25 and Hk = 0.14. If the wheel rolls while slipping, determine the magnitude of the linear acceleration of point G (in m/s2). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s?. M G
2. A cord is wrapped around a homogeneous disk of radius r = 0.5 m and mass m = 14. 25 kg. If the cord is pulled upward with a force T of magnitude 171 N, determine a. the acceleration of the center of the disk, b. the angular acceleration of the disk, c. the acceleration of the cord. T 0.5 m Go A Draw the Free Body Diagram.
The 544g collar is free to slide on the smooth rod OA. The rod rotates about pin O at constant angular velocity, é. a =en + še, = a = RÔ?e, + RÖe, for a circular path, R = radius 2.1 Use N-T coordinates, draw a FBD and a kinetic diagram to determine the minimum value of é for which the collar will maintain contact with the stop at A throughout the rotation. 2.2 Would friction between the collar and the rod affect your result in 2.1?
4. A uniform disc of mass m = 3 kg and radius R= 0.5 may roll without slip on the 30 degree incline shown. An elastic spring of stiffness k= 100 newtons/meter is connected to the center C of the disc. Initially, the disc is held in place in the position shown, with the spring neither stretched nor compressed and with the disc at rest. At t = 0 the disc is released and is subjected to a constant force of Fo = 30 newtons along the incline. Determine the maximum speed achieved by the disc center C as the disc moves up the incline. For gravity use g = 10 m/sec². (note: initially the constant force Fo will be greater than the forces exerted by the spring and by gravity, and the disc will accelerate up the incline; but there will come a distance x along the incline after which the spring force + gravity will overtake the force Fo, and the disc will then decelerate). gravity Fo= 30 N 30° no friction
The parallelogram linkage shown moves in the vertical plane with the uniform 9.3-kg bar EF attached to the plate at E by a pin which is welded both to the plate and to the bar. A torque (not shown) is applied to link AB through its lower pin to drive the links in a clockwise direction. When e reaches 51°, the links have an angular acceleration and an angular velocity of 7.0 rad/s² and 2.3 rad/s, respectively. For this instant calculate the magnitudes of the force F and torque M supported by the pin at E. Welded 1435 mm pin F 995 995 mm mm B D Horizontal Answers: F = i N M = i N•m
The slender, homogeneous rod shown in the figure below is 3 m in length and has a mass of 12 kg. At the instant shown, the rod has an angle to the horizontal of 60-degrees and an angular velocity of 2 rad/s clockwise. Both walls are smooth and provide negligible friction. At the instant shown, what are the reaction forces at A and B? What is the angular acceleration of the rod's center of mass?
The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of ? = 55° shown in the figure. Find the tension forces at the strings AB and AC.
A stepped cylinder has the dimensions R₁ = 0.30 m, R₂ = 0.65 m, and the radius of gyration, k, is 0.35 m. The mass of the stepped cylinder is 100 kg. Weights A and B are connected to the cylinder. If weight B has a mass of 80 kg, and weight A has a mass of 50 kg, how far does A move in 5 seconds? In which direction does it move? (Draw all FBDs)
A ring of mass m =1 kg and radius R = 1m is attached to a vertical shaft by means of a frictionless pin. Coordinates xyz are fixed to the ring as shown and the frictionless pin at A is aligned with the x-axis. The vertical shaft precesses about the Z-axis with constant angular velocity 2 = 1 rad/s. (a) At a particular moment when 0 = 30° and = 4 rad/s, find the value of Ö . This comes from a sum of the moments about the x-axis. Do not neglect gravity. (b) Find the torque or moment necessary that must be applied about the vertical shaft in order to keep it turning at a constant rate of N = 1 rad/s. Ring R XG A 1 Ixx = lyy =mR? G Iz = mR?