A 3m both ends hinged timber column is made of Apitong wood with the following properties: Fc = 9.56 MPa (parallel to grain) Fc = 2.20 MPa (perpendicular to grain) E = 7310 MPa If it has a square section with 200mm side dimension. Compute the actual slenderness ratio of the column. a. 12 b.13 c.14 d.15

A 3m both ends hinged timber column is made of Apitong wood with the following properties: Fc = 9.56 MPa (parallel to grain) Fc = 2.20 MPa (perpendicular to grain) E = 7310 MPa If it has a square section with 200mm side dimension. Compute the actual slenderness ratio of the column. a. 12 b.13 c.14 d.15

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.5.15P

See similar textbooks

Similar questions

7 7a 7b 7c Alaterally supported beam was designed for flexure. The beam is safe for shear & deflection. The most economical section is structural tubing however the said section is not readily available at the time of the construction. If you are the engineer in charge of the construction what alternative section will be the best replacement? Why? The section is 8" x 8" x 7.94 mm thick: Use Fy=248 MPa: E=200,000 MPa AISC wall thickness Ix 106 S x 103 Jx 103 mm4 mm3 mm4 rx =ry Area Ag (mm2) mm Designation Weight/m 8x8 7.94 47.36 6,039 79.25 37.84 371.99 60.35 expla'n briefly your cho'ce. (transform your comparative analys's 'nto a narative form to support your cho'ce) 8x8 14.29 80.61 10,258 76.2 59.52 585.02 99.06 8x8 72.7 9,290 76.96 54.53 539.13 90.32 8x8 9.53 56.09 7,161 78.48 44.12 432.62 70.76 mm 12.7 Zx 103 mm3 437.53 714.48 650.57 512.92
Design the reinforcements of the given T beam below. bf=800mm bw=450mm tf=120mm d=600mm d'=80mm fc'=35MPa fy=350MPa USE NSCP 2015 A.Mu = 1300kN-m, As = B.Mu = 1600kN-m, As = mm2 _mm2, As' = mm2
A built-up section shown, 30 feet long, is fixed at both ends and braced in the weak direction at the midheight. A992 steel is used. Determine the following: 11. Ix 12. Ky 13. effective slenderness ratio 14. Fe 15. LRFD design strength 16. ASD allowable strength 18 4 W10 × 49 A 14.4 in² bf 10 in d. 10 in tw 0.340 in tf 0.560 in Ix= 272 in¹ Iy=93 4in¹ W10×54 A 15-3 in² bf 10 in d = 10 lin tw0-370 in tf 0.615 in Ix= 303 in 4 Ty = 103 in 1
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.a) Determine the design tensile strength of the section based on yielding of the gross area.b) Determine the critical net area of the connection shown.
A tie member of a roof truss consists of 21SA 100 x 75 x 8 mm. The angles are connected by fillet weld as shown in figure on either side of a 10 mm gusset plate and the member is subjected to a factored pull of 450 kN. Take size of weld as 6 mm and connections are made in workshop. [Use Fe410 grade of steel] 75 m L. C. = 31mm 16A (100 x 75 x 8) mm Choose the nearest correct statements: L1 = 390.5 mm L1 = 195.25 mm Correct Option L2 = 87.75 mm Correct Option L2 = 175.5 mm
Centroid + Inertia 200 x 20 mm Plate The strength of the rolled section shown is increased by combining S section, channel, plate and then welded. 1. Determine the location of its centroid; and 5310 x 47.3 C310 x 30.8 2. Determine the moments of inertia of the composite section with respect to its centroidal x and y Semi-circle Weld, 10mm radius axes.
3. A plate with width of 300mm and thickness of 20mm is to be connected to two plates of the same width with half the thickness by 24mm diameter bolts, as shown. The rivet holes have a diameter of 2mm larger than the rivet diameter. The plate is A36 steel with yield strength F,-248MPa and ultimate strength F,-400MPa. a. Determine the design strength of the section. b. Determine the allowable strength of the section 24mm 30mm
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. a) Determine the allowable tensile strength of the section based on tensile rupture of the net area.b) Determine the allowable tensile strength of the section based on yielding of the gross area.
Determine the force of the members for the space truss shown in the figure. Joints A and B are supported by ball-and-socket while Joint C is supported by short link along z-axis. Indicate whether member is tension (T) or compression (C). 2m y Sm Az By BX Bz PAR Ax CSXScanned with Ca canner a SISU KN 15m 1 2117
Compression members
A PL 38 X 6 tension member is welded to a gusset plate as shown. The steel is A36 (Fy = 36ksi, Fu = 58ksi). a. The design strength, Pu based on gross area b. The design strength, Pu based on effective area PL % x 6 3/8" 6" Cross Sectional area of PL3/8x6 a) Blank 1 b) Blank 2 Blank 1 Add your answer Blank 2 Add your answer
أ.د. رمضان المبروك A PL170mm x 10mm tension member is welded to a gusset plate as shown in Figure below. The steel is A36. Assume that Ae = Ag and compute the following. %3D fy = 250 MPa & f, = 400 MPa %3D %3D PL 170mmx10mm a. The design strength for LRFD. . The allowable strength for ASD. roblem (4):