Do it ASAP x=7 x-8A 3-phase Y-connected induction motor is connected to a (240+XY) volts, 60 Hz power supply. Thenumber of poles are 4 and per phase parameters are R1 = (0.5 - X/100) 2, X, = 0.7Y 2, R2 = 0.4 2,X2 = 0.9X 2, and Xm = 40 2. The per phase core loss is 45 W, and the total frietion and windage lossis 160 W. When the motor operates at a slip of 4 %, determine:a. The input currentb. The power developedc. The shaft torqued. The efficiency of the motor.

In this question, 3 phase induction motor parameters are given. Find the imput current, Power…

A 3-phase Y-connected induction motor is connected to a (240+XY) volts, 60 Hz power supply. The number of poles are 4 and per phase parameters are R1 (0.5 - X/100) 2, X, 0.7Y 2, R2 0.4 2, X: = 0.9X 2, and Xm = 40 2. The per phase core loss is 4s w, and the total friction and windage loss is 160 W. When the motor operates at a slip of 4 %, determine: a. The input current b. The power developed c. The shaft torque d. The efficiency of the motor.

A 3-phase Y-connected induction motor is connected to a (240+XY) volts, 60 Hz power supply. The number of poles are 4 and per phase parameters are R1 (0.5 - X/100) 2, X, 0.7Y 2, R2 0.4 2, X: = 0.9X 2, and Xm = 40 2. The per phase core loss is 4s w, and the total friction and windage loss is 160 W. When the motor operates at a slip of 4 %, determine: a. The input current b. The power developed c. The shaft torque d. The efficiency of the motor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5) W. bridge at state of balance when first arm 1000, second arm 2000, third arm 1002 and forth arm 20002. If we put resistance 50 on the forth arm to be 2005o, when the sensitivity of the Galvanometer 0.5 mm/uA. This Galvanometer can be discover the state of unbalance if the source value is 5 volt.(right or wrong?)
A Platinum RTD thermometer has a resistance of 136 ohms at 90 degrees celsius,if it's resistance increases to 280 ohms when it is in contact with hot gas. Determine the temperature of the gas. Take the resistance of RTD to be 100 ohms at 0 degrees celsius
Q.1. (a) Briefly explain how a galvanometer is converted into a Voltmeter. Draw the circuit for fixed & multi range Voltmeter and write equations for Rs. (No simulation is required, only paper work) (b) What is loading effect in Voltmeter?
Please answer with explanation...
Task 1: a) Explain how you would practically test the accuracy of an electronic thermometer. b) Using TINA-TI: i) Create a circuit that will read the voltage output of a thermistor. ii) Run a DC analysis of the system monitoring the system between 0•CC and 100•CC. Displaying your results on a graph. c) Explain the advantages and disadvantages of practical testing and simulations, compare the two and explain why both are important when developing the final system.
Explain the basic principles of voltage regulation in a power system.
Question 1 AC supply voltage with f=50-Hz is connected to a bridge rectifier via a step-down transformer if the rectifier output is connected to a resistive load with 472 and the output power seen across the resistor is 2.5-watt a) Calculate the output peak voltage and current b) Calculate the secondary and primary ms voltages seen across the transformer c) Calculate the secondary and primary peak-currents seen across the transformer ) Draw the output instantaneous voltage and current showing the relevant peak and DC quantities c) Derive the instantaneous equations for the output ac voltage and current (seen across the resistor) Hint: use the 2" approximation (practical model) N-100 turns N-20 turns D3 DI f= 50 Hz D2 D4 R=470 R-2.5w
What is the answer for Question 10
A device used to protect a circuit against over currents is a what? a. Polyswitchb. Capacitorc. Dioded. Resistor
Describe the method of measuring temperature using RTD and using a thermocouple, its advantages and disadvantages. How to install between the 2 methods.
Question 4 (a) A PMMC movement with a coil resistance of 25 0 requires 0.8 mA for full scale deflection. Specify: a. The coil voltage required for full scale deflection. b. The shunt resistance required for a 0-1 A ammeter. c. The multiplier resistance required for a 0-10V voltmeter. d. Draw both instruments.
As an electrician what should you bear in mind when you working with electric