Answered: In a solar dish, which device converts…

In a solar dish, which device converts the thermal energy of fluid into mechanical energy? O a. gas turbine O b. steam turbine O c. generator O d. heat engine

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: An energy meter revolves 190 revolutions of disc for a unit of energy. Find the number of…

A: Need to find the number of revolution for the given load conditions then find error

Q: Bimetallic strip could be used as a temperature detector. Explain its working principle and show…

A: Bimetallic thermometer is a device to which can be used to convert a temperature into mechanical…

Q: What is a “spark spread”? a. The difference between the price of electricity and fuel cost b.…

A: Correct answer is option C Spark spread is defined as the difference between the price of the…

Q: a. Determine the time constant. b. Write the mathematical expression for the current i̟ after the…

A: According to guidelines we are allowed to do only first 3 subparts. post again for remaining as…

Q: a) A sinewave is having a frequency of 50 Hz and instantaneous value of 250 Volts at 1.2 milli…

Q: the ability of a material to generate an electric charge when subjected to pressure a. Piezo…

A: In this we will write about piezo electric effect...

Q: 2.2 Suppose a sinusoidal voltage of ±10 V with a frequency of 500 HZ is to be displayed on an…

A: The given problem is from measurements and instrumentation. The detailed solution is given in the…

Q: The energy of turning the shaft of the dynamo while conducting the Laboratory Experienced DC dynamo…

A: Generating electricity sounds simple—and it is. The hard thing is that you need to put in a huge…

Q: 4 What type of conversion is happening in a DC Generator. a. DC electrical energy to…

A: A DC generator is an electrical machine. Which convert mechanical energy into electricity.

Q: what is process leads to lowering the number of free electrons? what is The Townsend's Criterion why…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Flowing wind has a. 72 percent of carbon dioxide b. Constant kinetic energy c. Variable kinetic…

A: Flowing wind have variable kinetic energy

Q: 78 The induced emf of a dc machine running at 750 rpm is 220 V. The percentage increase in field…

A: we need to determine percentage increase in the field flux.

Q: Q Advantages of rotating field in an Alternator? (Write five point with Explanation)

A: An alternator is a machine that transforms mechanical energy into alternating current (AC)…

Q: Identify the effect of the power coefficient for a wind turbine if the power extracted by rotor…

Q: A flat circular coil having 50 loops of wire on in has a diameter of 48 cm. What current must flow…

A: Given : A flat circular coil No of loops , N = 50 Diameter of coil = 48 cm , Radius = 0.24 m Flux…

Q: Is the equilibrium point C stable? Please describe your answer Load torque TL1 A Motor torque T Load…

Q: The gas turbine, diesel motor and steam turbine are called the of a generator to produce…

Q: The physical construction of two pairs of magnetically coupled coils is shown. Assume that the…

A: (a) The magnetically coupled coils are shown below: As per the direction of the fluxes, there are…

Q: R= バニスル | कि-30-

Q: A mechanical load of 0.5n moved by a 12 v linear motor with movable member of 0.2 meter long moving…

A: i) For the steady-state condition, the force on the mechanical load should be balanced. The force…

Q: SELECTOR SWITCH PUSHBUTTON SWITCH R, 250 DISCHARGE PATH CHARGE PATH 24V Ca10pF R=25KO Charge time =…

A: Brief description : Capacitor is an electrical element which is used to store the charges in the…

Q: 1. Formed when a wire in an electric circuit is wrapped around an iron core producing a magnetic…

Q: Voltage (Voltage) Regulator Alternators without Excitation Machine (Constant Voltage Generators)…

A: Voltage Regulators: A voltage regulator is an electrical or electronic device that can hold…

Q: The temperature range for the flash steam power plant is---- a. 350 F O b. 840C O c. 840 F O d. 350…

A: There is certain range of temperatures in flash stem power plants. based on the these range of…

Q: 7. When it is necessary to provide automatic control of the voltage output at constant speed, the…

A: Conceptual Background:- DC Generators:- An electrical device called a DC generator's principal job…

Q: Explain the importance of reactive power in electrical power systems and how it affects system…

A: Reactive power, denoted as Q and measured in volt-amperes reactive (VAR), is the power that flows…

Q: 3. Two coils are magnetically coupled. A current of 10 A in the first coil will produce a flux of…

A: The solution is given below

Q: The brushes of DC machines are usually made of and are in the shape of rectangular block. Select…

A: Brushes of dc machine are made of corbon graphite .and these are in rectangular shape.

Q: A 120 V motor draws 12 A when running at 3200 RPM. When the motor armature is momentarily stopped…

A: We need to find out the resistance of armature.

Q: Can V curve be plotted for an alternator. If yes then what is the difference between V curve of an…

Q: A)The left hand rule for a coil is such that if you were to hold a coil in your left hand with your…

A: The explanation is as follows.

Q: 5. A welder machine operates automatically as follows : 30A current in 10 seconds, 20A in 10 sec.,…

A: In this question we will find RMS value of given waveform....

Q: A DC machine running at 750 rpm has an induced emf of 200 V. Calculate (1) the speed at which the…

A: Given:

Q: current through the armature of a motor changes from +3.0-A to - 3.0-A in 0.0030 s. A 104- V induced…

A: We need to find out the inductance for given Change in current

Concept explainers

Electrical Heating Unit

The conversion of electrical energy to heat energy is known as electric heating. The heating system that converts the electrical energy to heat energy for various application is called electrical heating unit. Electricity is employed as the firing mechanism in electric heating systems, which transforms electric current to heat. Electric heaters have heating elements in the form of electric resistors.

Question

In a solar dish, which device converts the
thermal energy of fluid into mechanical energy?
O a. gas turbine
O b. steam turbine
O c. generator
O d. heat engine

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The sinewave has a peak voltage of 7 A and a Half cycle value of 9.3333 ms. What is the frequency? a. 214.28 Hz b. 321.42 Hz c. 53.57 Hz d. 35.71 Hz
Q4/ A square-wave (Fig.3) voltage of amplitude E = 100 V and frequency 60 Hz is applied on a coil wound on a closed iron core. The coil has 500 turns, and the cross-sectional area of the core is 0.001 m?. Find the maximum value of a. the flux and sketch the waveforms of voltage and flux as a function of time. b. E if the maximum flux density is not to exceed 1.2 T. E = 100 V 60 Hz Fig.3 t (sec) 1 60 - 100 V
What is a typical voltage used for capillary zone electrophoresis? a. 2.5 MV b. 250 kV c. 250 MV d. 25 V e. 2.5 kV f. 25 MV g. 250 V h. 25 kV
A coil consists of 750 turns. A current of 10A in the coil gives rise to a magnetic flux of 1200 Wb.Determine the inductance of the coil.
2. An armature has 268 coils and rotates at 900 rpm. Each brush covers 4 commutator segments. a) Find the time for one revolution . b) Estimate the interval during which a brush short circuits a coil. c) Why is your answer in part (b) approximate? 1000
Find the mechanical speeds in revolutions per minute of a multipole electrical machine, if the frequency of the generated voltage is 50 Hz for a two-pole machine a four -pole machine an eight-pole machine
High humidity in a production environment can cause adhesion problems. However, low humidity introduces this problem as well a. high pressure b. dry air c. low pressure d. static charge
A flux of 0.0016 Wb flows in a silicon sheet steel coil/core. The arrangement appears as shown below with the following dimensions: Ac = 0.0025 m? Core/gap area: Flux path length: le = 0.350 m lg = 0.0015 m N = 500 Air gap length: Number of turns: %3D A. What is the current, I, through the winding? B. What is the energy stored in the inductance? C. Assume that the current is given by i =9.75 sin (3147) A. What is the RMS voltage that would appear across the winding? D. Assume that the gap is removed from the arrangement with the flux path remaining at 0.350 m. For a flux of 0.0016 Wb, what is the inductance of the arrangement? E. What is the energy stored in the inductance with the gap removed?
A 220 V DC Machine supplies 20 A at 200 V as a generator. The armature resistance is 0.2 ohm. If the machine is now operated as a motor at the same terminal voltage and current but with the flux increased by 10 percent, the ratio of motor speed to generator speed will be
1. A 6 ampere supply has a frequency of 25 Hz. Find the instantaneous value of current a. at 0.00530 sec from zero going to the positive direction. b. at 0.00530 sec from zero going to the negative direction. c. at 530 degrees.
1. A motor a. b. machine C. electrical d. generator 2. The commutator connection in a wave winding has a distance of 350 a. b. is a mechanical device that can be used to converts energy. 270 C. 180 d. 360 3. How many parallel paths a 4-pole, duplex lap winding have? a. 2 b. 6 c. 8 d. 4 4. It is the distance between the commutator connection of a DC machine? a. Commutator pitch b. 360 electrical degrees c. Parallel paths d. Coil pitch 5. The distance between two coils sides. a. Commutator pitch b. 360 electrical degrees electrical degrees.
Q3: A universal fractional horsepower series motor has a resistance of 30 22 and a total inductance of 0.5 H. When connected to a 250 V d.c. supply and loaded to take 0.8 A, it runs at 2000 r.p.m. Estimate the speed and p.f. when connected to a 250 V a.c. supply and loaded to the same current.