A 3" diameter bar is supported by a smooth pin in C and a cable from A to B around the smooth peg at D. Find (a) the stress (psi) in the cable if its diameter is 0.6" and the bar weighs 2,500 lb/ft³; and (b) the shear stress (psi) in the 0.5" diameter pin at C. Neglect the weight of the cable, pins and other attachments.

A 3" diameter bar is supported by a smooth pin in C and a cable from A to B around the smooth peg at D. Find (a) the stress (psi) in the cable if its diameter is 0.6" and the bar weighs 2,500 lb/ft³; and (b) the shear stress (psi) in the 0.5" diameter pin at C. Neglect the weight of the cable, pins and other attachments.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

*2-8 Part of a control linkage for an airplane consists of a rigid member CBD and a flexible cable AB. If a force is applied to the end D of the member and causes it to rotate by 0.3°, determine the normal strain in the cable. Originally the cable is unstretched. 2-9 Part of a control linkage for an airplane consists of a rigid member CBD and a flexible cable AB. If a force is applied to the end D of the member and causes a normal strain in the cable of 0.0035 mm/mm, determine the dis- placement of point D. Originally the cable is unstretched. Fo A 400 mm- D R 300 mm 300 mm P
Bar ABC is supported by two cables and a h inge. Compute the new temperature of alumi num cable if the tensile stress of the steel ca ble is 30 MPa. The current temperature of th e system is 21 degrees Celsius. Assume tha t the new temperature will only affect the alu minum cable. Steel L = 0.9 m A = 300 mm² E = 200 x 10' N/m² a = 11.7 μm/(m °C) B 0.6 m Aluminum L = 1.2 m A = 1200 mm² E = 70 x 10' N/m² a = 23 μm/(m-°C) 1.2 m C
A homogenous bar AC with negligible mass is supported by a pin at A and cable BC, carried a load of 20 kN as shown in the figure. Determine the pin dieameter at A if the allowble shearing stress is 80 MPa. (double shear)
The tension of cable AC is 110 N. Determine the mass of the crate at point E. g=9.81 m/s² X A 3m E 2m Z -3m 6m B 2m
8-21 The offset link has a width of w = 200 mm and a thick- ness of 40 mm. If the allowable normal stress is σallow 75 MPa, determine the maximum load P that can be applied to the cables. P 50 mm P
The homogeneous bar AB weighing 1800 lb is supported at either end by a steel cable. Calculate the smallest safe area of each cable if the working stress is 18 000 psi for steel. 2ft 1.5 ft a. 0.075 in? c. 0.100 in? d. 0.050 in? 5ft b. 0.128 in? Ans:
The crate has an unknown weight W and is held by cable AB, AC, and AD. Each cable can hold a max of 450 pounds. There are the following coordinates: A(0,0,0) B(-2,1,2) C(-2,-2,1) D(3,0,0). Part A) Find the max weight W that the system can hold without breaking any cables Part B) Use the weight from part A to find the tension in the cables draw all FBDs please
Compute the safest minimum diameter of th e cables if the allowable axial stress of the c able is limited to 60 MPa. All cables have th e same diameter size. B 40" A 50 KN 80" 30° 50° 50 KN E
5-11. The assembly consists of two sections of galvanized steel pipe connected together using a reducing coupling at B. The smaller pipe has an outer diameter of 18.75 mm and an inner diameter of 17 mm, whereas the larger pipe has an outer diameter of 25 mm and an inner diameter of 21.5 mm. If the pipe is tightly secured to the wall at C, determine the maximum shear stress developed in each section of the pipe when the couple shown is applied to the handles of the wrench. 5-14. used Dete mm 75 N. 150 mm 200 mm 75 N Prob. 5-11
The homogeneous 48-N plate is welded to the vertical shaft AB of neg- ligible weight. The assembly is supported by a slider bearing at A and a thrust bearing at B. Determine the force in cable CD and the magnitude of the bearing reaction at A.
Determine the a) normal stress in rod (1), b) the shear stress in pin B and the shear stress in pin A given the following properties of the structure. The tie rod at 1 is 10 mm in diameter. Pin Pin Connection Diameter SET e a b h Connection Type at B & D of pins Type at A A 1300 N 45° 600 250 450 Double Single Shear 12 mm mm mm mm shear D (1) C b
Consider the truss structure and the loading given below. a) Compute the average axial stress on member AB, b) compute the average shear stress at the pin of connection A. d- 20 mm 600 mm 50 mm -S00 mm 60 kN 25 mm | I 20 mm 30 mm I20 mm 25 mm TOP VIEW OF MEMBER AB d = 30 mm