A 2m B w = 24 kN/m Figure 1. An overhang beam with constant EI, and is being supported by a pin at A and roller at B, with a free end at C. 1 m IC Part 2: Suppose, a vertical roller support is added at point C. Use only Area-Moment method. 1. Determine the degree of indeterminacy of the system. 2. Determine the Reaction force at C (in kN). 3. Determine the reaction force at A (in kN).

A 2m B w = 24 kN/m Figure 1. An overhang beam with constant EI, and is being supported by a pin at A and roller at B, with a free end at C. 1 m IC Part 2: Suppose, a vertical roller support is added at point C. Use only Area-Moment method. 1. Determine the degree of indeterminacy of the system. 2. Determine the Reaction force at C (in kN). 3. Determine the reaction force at A (in kN).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: what is the shear rupture capacity of the shear plate of the shear connection in kips? (2 decimal…

A: Shear plate thickness = 0.5 inA36: Fy = 36ksi, Fu = 58 ksieffective bolt hole diameter = bolt hole +…

Q: Find fr (modulous of rupture) = ? M, bending moment = ? k = ? j = ? y = ? I = ? 0

Q: f'=4,000 psi DL=only SW LL=150 Ib/ft f,=60 ksi y=150 pcf W=? B=24" 7.5"

A: The given data is: fc'=40000 fy=60 ksi yc=150 pcf DL=500 lb/ft LL=750 lb/ft L=25 ft

Q: 3028 70mm 300mm 500mm

A: b = 300mm d = 430mm f'c = 27.6 MPa fy = 345 MPa

Q: 12" fé= 3.5 ksi 30" 26" fy= = 40 ksi n = 9 As =8#6 Find fr (modulous of rupture) = ? M, bending…

A: Reinforced concrete beam: In a Structural Frame, the beam is the horizontal structural member which…

Q: 2) Determine the moment of Area of the given Built-up section about its centroidal axis.The top…

Q: Determine the height h above the base of the centroid of the cross-sectional area of the beam.…

A: Given,

Q: No. 9 bars compression bars in a column are to be lap spliced. There is no excess steel and the bars…

A: Given, Compression bar no. #9 is spirally reinforced with dia 3/8 inch and pitch 3 inches.…

Q: Problem 9: Approximate Analysis for Lateral Loads (Portal Method)

A: Certainly, I can provide you with a step-by-step calculation of the portal method for the given…

Q: ADAP PLS ANSWER CORRECTLY, do not round off the initial values, round off only in final ans plz

A: SG of sea water = 1.03 Density of sea water(Ps) = 1.03 ×1000kg/m³ Density of sea water(Ps) = 1030…

Q: Find (a) Ix 3 (b) Iy for the composite

Q: O Figure Q2b shows a solid and homogeneous section, where (31.25 mm, 41.54 mm) are its centroid…

Q: (1) 21" 3". 4#9 14" (1) Ec = ? (2) fr=? (3) Mer=? #4 (4) When M = 70 (5) & Mn = 2 fl=5 ksi Grade 60…

A: Given: fc = 5 ksi = 5000 psi fy = 60 ksi = 60,000 psi b = 14 in d = 21 in h = 24 in main bar =…

Q: A 100 kN block is on a plane inclined at an angle of 30° with the horizontal. Find the parallel…

Q: Determine whether the block shown is in equilibrium and find the magnitude and direction of the…

A: Given data:θ = 35° P = 196 N μs = 0.20 μk = 0.15F = 800 NThe mass of the block is not given, so we…

Q: (7) Let's practice moment of inertia calculations on this built-up cross-section. It is made of four…

Q: Determine whether the block shown is in equilibrium and find the magnitude and direction of the…

A: Step 1: Draw the FBDStep 2: Compute for the normal…

Q: Figure -20 mm y 10 mm Part A Locate the centroid y of the cross-sectional area of the beam…

A: a = 350 mm b = 370 mm

Q: Determine whether the block shown is in equilibrium and find the magnitude and direction of the…

A: Step 1: here we have calculated all the component forces Step 2: here we have calculated the…

Q: Q1. Identify all zero force members B E WW HL100 kN 160 kN

Q: 2k ↓ 3' n Hu 3k ↓ 5' UT 3t ↓ 5' 2x ↓ W w=14/f w 24*84. Find A. Include self-weight.

A: Rectangular beam of size 24 x 84 inLet's take, P1 = 4 kP2 = 2 KP3 = 3 KTotal length of beam, L = 26…

Q: A high-strength steel band saw, 23 mm wide, runs over pulleys 800 mm in diameter. What minimum…

Q: A uniform 25kg bar, 6.0m long is suspended by a cord shown. What is the tension in the cord? wall…

A: Given:-Weight of bar = 25 kg Lenge of bar=6 m

Q: Determine the following: a. How many additional ɸ16 tensile bars are required? b. What is the new…

Q: All members have a cross sectional area of A, and a Young's modulus of E. Calculate the horizontal…

Q: Determine whether the block shown is in equilibrium and find the magnitude and direction of the…

Q: determine the capacity of the details shown below. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi…

A: Thickness of beam (t)= 0.38 inbreadth of beam (b) = 7.07 indepth of beam (d) = 0.63 in

Q: Find Internal External Find and draw SMT Diagrams

Q: indeterminate? a) c) b) Hinge www

A: To check whether the structures given are indeterminate or not. Note: As per the guidelines of…

Q: I am always confused with the number of eq. I always use 3 equations, while you always use 2 in the…

A: The expert provided for solution d is wrong.Now I am providing the correct solution for you..

Q: The answer should have at least 2 decimal places. Solve in metric units. Use the following factors…

A: Note:- As the question is multipart question, so as per policy of bartleby we may provide answer to…

Q: 02 Determine the smallest allowable điameter brass rod, of length 3.Om, if the rod is to be twisted…

A: We need to find smallest allowable diameter of brass rod.

Q: A cylindrical rod .5" in diameter is subjected to an axial load of 11,300 lbs. A square bar of .5"…

Q: 2) Determine the moment of Area of the given Built-up section about its centroidal axis.The top…

Q: 4. A compression member 3 m long consist of two angles 150 x 100 x 10 mm with long legs back to back…

A: A compression member 3 m long consists of two angles 150 x 100 x 10 mm with long legs back to back…

Q: Determine the moment of inertia (mm4) ly of the composite area shown with respect to y-axis if a =…

A: Let Area 1 = Whole rectangular = (b + c) X a Area 2 = quarter circle with radius r Area 3 = Triangle…

Q: A flanged wooden shape is used to support the loads shown on the bear. The dimensions of the shape…

A: To Determine (a) the maximum tension bending stress at any location along the beam, and (b) the…

Q: The solid circular drill rod AB is made of a steel that is assumed to be elastoplastic with Ty= 22…

A: Length of shaft= 35 ft Applied Torque= 74kip-in

Q: 2) Determine the moment of Area of the given Built-up section about its centroidal axis.The top…

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

Take note of instructions for this Part, a vertical roller is added at point C from the figure being shown. Previous answer here was wrong, please answer correcrly.

A
2 m
B
w = 24 kN/m
Figure 1. An overhang beam with constant
EI, and is being supported by a pin at A and
roller at B, with a free end at C.
1m
C
Part 2: Suppose, a vertical roller support is
added at point C. Use only Area-Moment
method.
1. Determine the degree of
indeterminacy of the system.
2. Determine the Reaction force at C
(in kN).
3. Determine the reaction force at A (in
KN).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: calculate degree of indetrminacy

VIEW

Step 3: calculate reaction at B

VIEW

Step 4: calculate reactions at A&C

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 11 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

i need the answer quickly
2) Determine the moment of Area of the given Built-up section about its centroidal axis.The top flange is 8"X 1" and the stem is 16" X1" the bottom flange is 16" X 1.5", the angle bars are 2- 5"X3"X %. Tabulate your solution and Answers. + X.
note: SN is equal to 18, topload will be equal to 118kN.
The assembly is subjected to a vertical shear of V=55 kip Figure B- 2 in. 0.5 in. 0.5 in. 6 in.. 2 in. 0.5 in. 6 in. < 1 of 1 0.5 in. 0.5 in. Part A Determine the shear flow at point A (Eigure 1) Express your answer with the appropriate units. 9A= Submit Part B μA 9B = Value Request Answer HÅ Determine the shear flow at point B Express your answer with the appropriate units. Value lb in ● Submit Request Answer - 1) ? B ? lbin-1)
B2
P= 1900 lb 4 ft -3 ft- B ✓ P 3 ft- C P -3 ft Find CH, HG, HE, DE H D P Show Transcribed Text G E 3 ft 3 ft ✓ P P
PLEASE ANSWER ALL OF THIS QUESTION ASAP!!!
need asap
3.1 * PQ4 Apply the grid method b. If the pressure is 120 kPa abs, what is the gage pressure in psi?
Situation III: Given the grouped data for the strengths of the reinforcing steel bars. 7. Determine the mean. 8. Determine the median. 9. Determine the mode. Bar Strength Number of (MPa) bars. 240-269 7 270-299 11 300-329 4 330-359 17 360-389 22
I need correct handwritten and only do if you can do full question otherwsoe skip plss
Determine whether the block shown is in equilibrium and find the magnitude and direction of the friction force when 0=35° and P = 200 N. 800 N Hs = 0.20 Hk= 0.15 25° Previous