Refer to the given answer so that I will know how it came up. A 220 V, 3-phase voltage is applied to a balanced delta-connected 3-phase load of phase impedane (15 + j20) 2.Find:(ii) What is the power consumed per phase ?(i) The phasor current in each line.(iii) What is the phasor sum of the three line currents ? Why does it have this value ?|Ans. 15.24 A; 1161.6 W ; zero]

Answered: Image /qna-images/answer/ea7855fc-6859-49fa-8206-3736d2a273b6.jpg

A 220 V, 3-phase voltage is applied to a balanced delta-connected 3-phase load of phase impedanoe (15 +/20) Q Find: (i) The phasor current in each line. (iii) What is the phasor sum of the three line currents ? Why does it have this value? (i) What is the power consumed per phase ? JAns. 15.24 A: 1161.6 W; zerol

A 220 V, 3-phase voltage is applied to a balanced delta-connected 3-phase load of phase impedanoe (15 +/20) Q Find: (i) The phasor current in each line. (iii) What is the phasor sum of the three line currents ? Why does it have this value? (i) What is the power consumed per phase ? JAns. 15.24 A: 1161.6 W; zerol

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7MCQ

See similar textbooks

Similar questions

2. A three-phase transmission line has parameters Xc-6 k 2, R-3.25 2 and X₁-25 92, and delivers 300 MW to a load with both ends of the line at 230 kV. Draw a pi equivalent per-phase circuit of the line. On a per-phase basis, calculate the active power delivered to the load, the reactive power of the line and the active power delivered by the source. Based on these calculations can the equivalent circuit be simplified further?
AC Power and Power Factor 1. Two loads are connected in parallel across a 13,200-volt line. Load A draws 200kW at 0.6 p.f. (lagging), load B takes 200kVA at 0.8 p.f. (lagging). Find the reactive, apparent and true power and the line current.
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. Use Gauss-Seidel method in Matlab to analyze the system the tolerance of error is 10-3. Then anwser the questions as follows. V, = 1.05200 0.01+ j0.025 300 + j200 MVA 0.015 + j0.035 150 MW 200 +j150 MVA 0.01+ j0.03 |V = 1.03 The admittance matrix (Y_bus)? 0.02 + jo.04 0.0125 + jo.03 2.
10 Ω m I₁ j4 Ω + I₂ ~ Vs E₁ || 2:1 The load on the right is absorbing 650 W -j200 VAR. V₁ = 80 / 0° V. + V₁ I
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
A load of 138+j460 Ohm is supplied through 3+j14 Ohm line as shown in Figure 1. (a) Find the average power dissipated in the line. (b) Find the value of capacitive reactance connected across the load to compensate the reactive power need of the load. (c) What is the equivalent impedance after compensation. (d) Find the average power dissipated in the line when the capacitive reactance is connected across the load. (e) Express the power loss in (d) as a percentage of the power found in (a) j14 Figure 1 7200/0 + V (rms) Source 3 wi Line Load 138 j460
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
Use Millman’s theorem and determine the magnitude of the neutral displacement voltage,(Vsn) in the phasor form. Use Millman’s theorem and determine the phase voltage (Vbs) of the load in polar form. Use Millman’s theorem and determine the phase voltage (Vbs) of the load in polar form. Use Millman’s theorem and determine the current,(Ib) in phase b of the load in phasor form. Use Millman’s theorem and determine the current,(Ib) in phase b of the load in phasor form. Use Millman’s theorem and determine the reading on the wattmeter connected in line B of the circuit.
consider the following diagram of impedances in per unit of a common base a) get the YBUS admittance array and the ZBuz impedance array 213-j2 pu zt2-j0.15 zg2-j1.85 791-j0.9 211-0.1 1 212-j0.5pu 223-j0.5pu Va 1 p.u. Jv1-1p.u. 22-10 pu
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.