A 2000-kg homogeneous bar AB is suspended from two cables AC and BD, each with a cross-sectional area 500 mm2, as shown. Determine the location x of the largest additional force P which can be applied to the bar. The stresses in the cables AC and BD are limited to 90 MPa and 60 MPa, respectively. 1.8 m 1.8 m 2 tm

A 2000-kg homogeneous bar AB is suspended from two cables AC and BD, each with a cross-sectional area 500 mm2, as shown. Determine the location x of the largest additional force P which can be applied to the bar. The stresses in the cables AC and BD are limited to 90 MPa and 60 MPa, respectively. 1.8 m 1.8 m 2 tm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

This is the stiffness matrix for a horizontal roller, if the roller was vertical instead of horizontal, would rows 1/2 swap?
Using 0.45 power method to draw and compare between the aggregate gradations below. Sieve (mm) Gradation I Gradation II 25 100 19 95 100 95 12.5 87 70 9.5 77 57 4.75 56 38 0.6 2.36 1.18 42 30 23 25 17. 12 0.3 0.15 17 12 9 6 0.075 9 4
Given the following data: A. Loose Unit Weight Determination Fine Aggregate a. Weight of measure, g. 250.00 b. Weight of measure + sample, g. 8,750.00 c. Weight of sample, g. (b) – (a) d. Volume of measure, cm e. Unit weight, g/cm 1.016 Determine the height in cm of bucket if V=3.1416(22.4cm)*(height)/4 Continues computation and write your answer in 2 decimal places
Calculate the fineness modulus.
In the figure, two stamps (coins) with diameters D = 25 mm and d = 20 mm will be cut with a cutting die at the same time.Since the maximum cutting (molding) force that can be used is 2500 daN (F = 2500 daN), the maximum cut that can be cutfind the thickness (t) of the sheet material? The shear strength of the sheet material is 11 daN / mm2.
Given a. S is the last operation; P is the first operation b. A follows O c. M & L can both start in parallel after completion of P. d. H follows L e. Both B & E can be done concurrently, but only after the finish of M f. B precedes O g. M restrains the start of R, which follows the completion of H h. R precedes G i. E & R must both be finished before G starts j. A cannot start until both the completion of O and E k. A and G finish together, and S cannot start until they are both done. Draw the Network.
need help...thnks..
G...Discuss on the various costs associated with aggregate
Ox=30 Oy = -50 T₂ = -20 koj 2 Ох
Notice: This is only for REVIEW PURPOSES, this is NOT GRADED. A 100 block is in equilibrium. What is the magnitude of the frictional force between this block and the surface? Given: Us = 0.3 2 lb Options: A. 0 lb B. 1 lb C. 2 lb D. 3 lb E. Othe answer
Help asnwer this, thanks.
Bond, Anchorage and Development Length Question 1: How much shall be the development length of 25 mm diameter deformed reinforcing bar of grade Fe415 in tension? (Given that design bond stress in limit state method for deformed bars in tension = 2.24 N/mm2) 1. 762.9 mm 2. 1220.6 mm 3. 1007.39 mm 4. 849.5 mm