A 200-V, 100 A armature full-load line current, 1500 RPM, shunt DC motor is consideredin this problem. Its characteristics are given below:RA =0.20 S2RF= 250 2NF=2000 turnsThis motor has compensating windings and interpoles.The magnetization curve for this motor at 1500 RPM is shown in a tabular form below:If,A0.1 0.2 0.40.50.60.81.01.21.61.82.02.22.4EA.V 6.0 2550110 135 160 205 235 255 275285 288 290 291For Radj between 150 2 and 2502, find the range of no-load speed of this motor.Select one:O a. Range of speed between 1222 RPM and 2360 RPMO b. Range of speed between 2222 RPM and 2727 RPMOC. NoneOd. Range of speed between 1818 RPM and 2220 RPM

Answered: Image /qna-images/answer/0612c2a1-0b6d-443d-a724-b7ec0a74b779.jpg

A 200-V, 100 A armature full-load line current, 1500 RPM, shunt DC motor is considered in this problem. Its characteristics are given below: RA =0.20 S2 RE= 250 2 NF= 2000 turns This motor has compensating windings and interpoles. The magnetization curve for this motor at 1500 RPM is shown in a tabular form below: Ir.A 0.1 0.2 0.4 0.5 0.6 0.8 1.0 1.2 1.6 1.8 2.0 2.2 2.4 EA.V 6.0 25 50 110 135 160 205 235 255 275 285 288 290 291 For Radj between 150 2 and 2502, find the range of no-load speed of this motor. Select one: O a. Range of speed between 1222 RPM and 2360 RPM Ob. Range of speed between 2222 RPM and 2727 RPM C. None Od. Range of speed between 1818 RPM and 2220 RPM

A 200-V, 100 A armature full-load line current, 1500 RPM, shunt DC motor is considered in this problem. Its characteristics are given below: RA =0.20 S2 RE= 250 2 NF= 2000 turns This motor has compensating windings and interpoles. The magnetization curve for this motor at 1500 RPM is shown in a tabular form below: Ir.A 0.1 0.2 0.4 0.5 0.6 0.8 1.0 1.2 1.6 1.8 2.0 2.2 2.4 EA.V 6.0 25 50 110 135 160 205 235 255 275 285 288 290 291 For Radj between 150 2 and 2502, find the range of no-load speed of this motor. Select one: O a. Range of speed between 1222 RPM and 2360 RPM Ob. Range of speed between 2222 RPM and 2727 RPM C. None Od. Range of speed between 1818 RPM and 2220 RPM

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1- To control the speed of an induction motor, the supply frequency is reduced by 10%. For the same magnetizing current to remain constant, the supply voltage must be....... a) Reduced by 10%, b) Reduced by 20%, c) Increased by 10%, d) Increased by 20% 2. When maximum starting torqua ic ohtoinod
Q / What is the benefit, purpose and conclusions of making single-phase induction motors ..?
QUESTION 2 a) Draw the equivalent circuit and torque-speed characteristic curve for a series DC motor. b) Briefly explain the induced torque occurs in a series DC motor. e) A 20-hp 240-V 76-A 900 rimin series motor has a field winding of 33 turns per pole. Its armature resistance is 0.09 2, and its field resistance is 0.06 2. The magnetization curve expressed in terms of magnetomotive force versus Ex at 900 rimin is given by the following table: Table Q2 c): The magnetomotive force table for a de motor taken at 900r'min E. V 95 150 188 212 229 243 F.A tuus 1000 1500 2000 2500 500 3000 If the motor running at 33 percent of the full-koad armature current, determine: ) The motor's power converted from electrical to mechanical form, Prene i) The motor's torque, Tnit ii) The motor's speed, n
Sketch the torque versus speed characteristic for a series-connected dc motor.
8) A 230 V fed single quadrant chopper has a 40% duty cycle. A separately excited DC motor is controlled by a chopper. Motor has a back emf constant of 0.5 V/rad/s and 2 22 armature resistance. Determine the torque of motor at speed of 1400 rpm 4.7 N-m 15.44 N-m 10.5 N-m 19 N-m
The schematic and torque-speed characteristics of a series wound DC motor are shown below : Field winding DC Supply Eb speed Torque - T-K, I, Field Flux = ø = Kla (i) According to the equations given above, explain why the torque of the series-wound DC motor is so high at low speed. Give application examples that require such torque-speed characteristics. A series-wound DC motor should never be started with light or NO LOAD. Give reason. (ii) (iii) Armature anbio
Discuss the advantages of flux weakening operating regime in a DC motor.
B/ fill in the blanks: The power factor of a squirrel cage induction motor is.... at light load only. 2. The eddy current loss in an AC electric motor is 100 watts at 50 Hz. Its loss at 100 Hz will be... 3- The rotor power output of a 3-phase induction motor is 15 KW and corresponding slip is 4%. The rotor copper loss will be.... 4- The resistance representing mechanical output in the equivalent circuit of an induction motor as seen from the stator is:.....
• Q5/ in a DC motor. List and describe the types of losses that occur
. Explain how the pulsating mmf of a single-phase induction motor may be considered equivalent to two oppositely-rotating fields. Develop an expression for the torque of the motor. A 125-W, 4-pole, 110-V, 50-Hz single-phase induction motor has the no-load rotational loss of 25 watts and total rotor copper loss at rated load of 25 watts at a slip of 0.06. At a slip s = 0.06, what is the power input to the machine ?
Draw the torque speed characteristic of separately excited dc motor showing the effect of changing the excitation current on it.
A 300 V D.C. shunt motor runs at 300 r.p.m. ,takes 10 A and induces the emf of 50V. The armature and field resistance is 20 ohms and 200 ohms respectively. The 200 ohm is added to field circuit increase speed to 900 r.p.m. . Assume flux proportional to field current. Then induced emf during 900rpm is (estimated time 2 minutes) a.75 V b.300 V c.200 V d.100 V