A 200 mm 50 mm Fixed to ground B 200 mm 2000 KN X A block of rubber 50 mm thick is sandwiched between two steel plates measuring 200 mm on each side as shown. A horizontal force of 2000 kN is applied to the top plate while the bottom plate is fixed to the ground. In response to the applied force, the top plate moves 5 mm in the direction of loading. a) Determine the average shear stress between the plate and rubber. b) What is the shear strain at point A and point B relative to the x-axis?

A 200 mm 50 mm Fixed to ground B 200 mm 2000 KN X A block of rubber 50 mm thick is sandwiched between two steel plates measuring 200 mm on each side as shown. A horizontal force of 2000 kN is applied to the top plate while the bottom plate is fixed to the ground. In response to the applied force, the top plate moves 5 mm in the direction of loading. a) Determine the average shear stress between the plate and rubber. b) What is the shear strain at point A and point B relative to the x-axis?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Homework 8: A (20°C) a rigid beam in placed upon the rods shown in figure: 1) Determine the magnitude of uniformly distributed load w (kN/m) so that beam remains horizontal when temperature of steel becomes to (100°C). 2) Find the stress developed in each rod. Steel A, = 1000mm², as = 12 * 10-6 , E, = 200GPA, L = 500mm %3D %3D Aluminum Aal 1500mm2, aal = 23 * 10-6 , Eal = 70GPA, L = 300mm %3| Rigid beam w (kN /m) A C steel Aluminum 3m 3m
A rectangular steel block is 3.2 inches long in the x-direction, 2.9 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 48 kips tension in the x-direction, 65 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places
Two steel plates each of width 150 mm and thickness 10 mm are connected with three 20 mm diameter rivets placed in zig-zag pattern. The pitch of the rivets is 75 mm and the gauge is 60 mm. If the allowable tensile stress is 150 MPa, then the maximum tensile force that the joint can withstand is
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm? A = 400mm? A - 200mm 40KN 10KN 20KN 2.5m 2.0m 1.5m
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN. 0.8m 0.4m B 5KN 0.6m Al 20KN Q2 5) What is the deformation 8, in mm? A=800 mm? A=1,200 mm?
Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm A = 400mm? A- 200mm 40KN 10KN 20KN 1.5m 2.5m 2.0m Determine the change in length of steel rod having a length of 800mm and a diameter of 6.5mm. The rod is subjected to a force P equal to 110KN. Young's Modulus is 200GPA Compute normal strain of the rod
Shown is a copper bar which has a diameter of 10 mm and loaded by tensile loadP = 0.0137 MN The maximum shear stress in the bar is approximately: Match each item to a choice: Tmax
For the state of stress shown, determine (a) the principal stresses, (b) the maximum in-shear stress. Sketch such stresses in a two- element format. 60 MPa 90 MPa Lx 30 MPa
The 919-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 321 mm2. Find the location x (in mm) of P that can be safely applied to the bar if the stresses in AC and BD are limited to 112 MPa and 57 MPa, respectively. Express your answer in two decimal places.