1. Calculate slab dead load intensity in kPa (kilo Pascal = kN/m²) in a main floor condobuilding, given the following parameters:- Allow for 0.3kPa for M&E (i.e. Parkade mechanical and electrical like for exampleducts, light fixtures etc..).Minimum allowance for partition walls as per ABC2019175mm concrete slab0.2kPa for tiling allowance (including tiles, adhesive, and grout)

Step 1: Calculate the weight of the concrete slab. Weigh of concrete slab = (175mm x 1m x 1m) x…

ing, given the following paramete Allow for 0.3kPa for M&E (i.e. Parkade mechanical and electrical like for exampl ducts, light fixtures etc..). Minimum allowance for partition walls as per ABC2019 175mm concrete slab 02kPa for tiling allowance (including tiles adhesive and grout)

ing, given the following paramete Allow for 0.3kPa for M&E (i.e. Parkade mechanical and electrical like for exampl ducts, light fixtures etc..). Minimum allowance for partition walls as per ABC2019 175mm concrete slab 02kPa for tiling allowance (including tiles adhesive and grout)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Estimate the tile work, ceiling and paint of a two storey residential building with the 14.3m x 8.5m…

Q: Given apartial structural firewall, compute for: a. Concrete materials b. Masonry materials

A: Given:- A partial structural firewall is given The firewall consists of two columns The dimension of…

Q: Double stud walls are a way to provide enough insulation to build a net-zero energy home. In some…

A: The thickness of the gypsum board = 1 in The dimension of the southern yellow pine boards = 2×4 The…

Q: Answer correctly ty

A: i) divide the length of the gutter by the effective width covering of one sheet , refer to the…

Q: For excavation of the exterior footings use a height of bottom of sand that is under the SOG to…

A: Calculating the excavation

Q: 1. Give the dead load in psf for the floor and wall section below. Do not round 3/4" wood paneling 4…

A: Floor section - 3"4 ceramic tile 2-1"2 normal weight concrete 1-1"8 plywood 7"8 wood lath and…

Q: Outside wall Insulation Pipe R loss

A: The given figure is heating pipeline and the various comparisons are made to know more about the…

Q: What is the minimum distance required for a vent termination on a roof with a 13/12 roof pitch? feet

A: Vent termination:- The vent pipe must end outside of the building at a range that is not less than 2…

Q: The backup wall in a brick veneer wall assembly consists of a (choose from below options):…

A: The non structural part made with bricks and backed by air cavity is known as brick veneer wall.

Q: EA Calculate number of Rolls of Asphalt Felt to cover the Roof Slope Area. (1 roll of Felt will…

A: Given Data, Length=32' Width=44' Area of the roof- Area of Roof=44×32×12217212Area of…

Q: Define fan efficiency.

A: Engineers will sometimes force air through a given system by using fans to regulate the internal…

Q: Define Chemical grouting.

A: Grouting is a technique of ground improvement to promote the construction of foundations and…

Q: How to apply waterproofing and damp proofing?

A: It is used to stop water infiltration through concrete structure. Water proofing materials have the…

Q: Step 2 is not very clear

Q: Determine the number of 25kg-bags of tile adhesive that will be used for tileworks in the DINING…

Q: Define Glazing alongwith Glazing large Lites.

A: The process of fixing aluminum or different materials like glass panes to the curtain wall…

Q: The indicated wall must be painted after insulation is installed. Find in squarefeet the area of…

A: Given: Length of wall, L = 10 ft Height of wall, H = 8 ft

Q: concrete stair and landing reinforments: -the trend bars 3-D 10 mm -the riser bars D-10 mm @ 150…

A: In concrete stair case This is a typical stair case details

Q: 은

A: Here, we need to addition for this problem Add= (2+2) = 4

Q: What assembly of materials is often used in a firerated partition that also requires effective…

A: The result of sounds emitted from an origin including a human communicating or a gate shutting is…

Q: Name: Heat Load Problem Set #1 Problem 个N' 2'8 X 4'0 1. nswer 2'8 X 4'0 Room 3: 10' X8' What is the…

A: Doors area is to be calculated for required heat gain

Q: Discuss pulse-jet cleaning methods in detail.

A: Solution: The technique of pulse-jet cleaning is widely used in the application of industries…

Q: Differentiate between optical and extra clean glass

A: Optical glass is mainly produced in a continuous melting process. Optical glasses acquire their…

Q: True or False 1. If more than one layer of roofing is needed along the roof slope, determine their…

A: 1. True. For the second layer of roofing, it gets difficult to determine the amount of material…

Q: In what way is a slope glazing system more difficult to make watertight than a wall cladding system?…

A: Slope glazing system: Sloped glazing system is used in buildings in which exterior cladding is…

Q: How an air stripping column works?

A: In air stripping method, moving air is passed through contaminated water through which contaminants…

Q: advantage of groundwater

A: Groundwater is the water which is found below the surface of the Earth within the cracks and spaces…

Q: Why is attic ventilation important?

A: attic ventilation is important:

Q: Define Vacuum Consolidation.

A: Vacuum consolidation is defined as the technique which is used for improving the property of soft…

Q: Define Wick Drains.

A: Wick drains are installed in soft soils to improve soil consolidation by providing extra drainage…

Q: Roof Sheathing Panels in High Velocity Hurricane Zone (HVHZ) shall have nail spacing 4 in. o.c. at…

A: High Velocity Hurricane Zone (HVHZ) is a building code that is used to differentiate the areas hit…

Q: rence between a two way flat slab and two way flare plate

A: Both Two way flat slab and two way flat plate are structural systems used in building construction…

Q: RAFTE AND

A: GIVEN- ROOF SLOPE- 712 Common rafter 16" run of common

Q: What is semidry scrubbing system?

A: Solution: Semi Dry Scrubber can be think about an an intermediate that is between the wet scrubber…

Q: Define Jet grouting.

A: Jet grouting is a soil stabilization process that involves injecting a stabilizing fluid into the…

Q: What are the four basic types of ducts used?

A: The cooled air from the unit of air conditioning is circulated by the Ductwork throughout the home.…

Q: Water-Drainage Exterior Insulation and Finish System

A: Answer Exterior insulation and finish system define as a general class of the non-loa bearing system…

Q: 8.a. Equipment rated at 1200 A or more and more than six feet wide that contains overcurrent…

A: Given data- 8(a) 1200 A rating6 ft or more in width

Q: acoustical control system

A: It is the engineering of getting best possible sound within the walls of a building ,considering…

Q: Research 5. 1st floor and attic floor wall details (wood)

A: Because the high cost of new construction prevents homeowners from adding square footage to their…

Q: What is the heat load of the top floor?

A: heat load is termed for building in several manners, the heating load acting on top of roof or top…

Question

1. Calculate slab dead load intensity in kPa (kilo Pascal = kN/m²) in a main floor condo
building, given the following parameters:
- Allow for 0.3kPa for M&E (i.e. Parkade mechanical and electrical like for example
ducts, light fixtures etc..).
Minimum allowance for partition walls as per ABC2019
175mm concrete slab
0.2kPa for tiling allowance (including tiles, adhesive, and grout)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Pricing masonry, carpentry and finishing work

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the clear wall R-value of a typical 2X6 stud wall assembly? Assume the following: (1)cavity has dense pack cellulose at R 22 (2)there are 1 percent air gaps in the cavity insulation with a nominal R value of 1 for the air gap (3)the framing factor is 22 percent with an R value of 1.25/inch (4) There is 1 inch of continuous XPS (R5/inch) on the exterior (5)Assume the air films, sheathing, facade, and wallboard add an additional 1.5 R value to the wall. Hint: draw this out. Answer:
Describe the core barrels as single wall or double wall.
Compare sand and flow plumbing
please help
I need the answer as soon as possible
What is the height of the finished ceiling in this room?
Describe the key differences between unitized and stick frame curtain wall systems in terms of design, installation, and thermal performance.
A fuel line must pass through this wall. Find in inches the length of the holethrough the wall.
Define tremie pipe
FIRSTLINE Which one of the following would support coordinating concrete formwork relative to the structural design? esc Temporary Works Trade Coordination Clash Detection Schedule Simulation 46°F Sunny Ơ
.In the reinforced beam section shown in the figure (not drawn to scale), the nominal cover provided at the bottom of the beam as per IS 456-2000, is 50 2-286 3-166 x 50 2-legged, 12 strrups@90c/e X 50
In the plan below there is a conventional L shape stair, the distance between slabs is 2.9m/? find the followings: height ise Assum/hat ar to 16.1 f T'ind the Fr C/ Find the tread width. D/ If the provided area of stair is (2m*3m), check it the area is enough for installation the tair or not? Assume it the stair width is 90 cm. 50-0 OPEN BED ROOM 11-7 X14'-0" LIVING 11-7 X17-10.5" 6-6X4-6" DRAWING 10-0X11-0 25'-0" BATH 8'XS BED ROOM 11-7 X14-0 KITCHEN 11-7 X8-0" PORCH 13-1.5X20-4.5"