A 200 gallon tank initially contains 100 gallons of water with 20 pounds of salt. A salt solution with 1/5 pound of salt per gallon is added to the tank at 10 gal/min, and the resulting mixture is drained out at 5 gal/min. Let Q(t) denote the quantity (lbs) of salt at time t (min). (a) Write a differential equation for Q(t) which is valid up until the point at which the tank overflows. Q' (t) = (b) Find the quantity of salt in the tank as it's about to overflow.

A 200 gallon tank initially contains 100 gallons of water with 20 pounds of salt. A salt solution with 1/5 pound of salt per gallon is added to the tank at 10 gal/min, and the resulting mixture is drained out at 5 gal/min. Let Q(t) denote the quantity (lbs) of salt at time t (min). (a) Write a differential equation for Q(t) which is valid up until the point at which the tank overflows. Q' (t) = (b) Find the quantity of salt in the tank as it's about to overflow.

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter1: Fundamentals Of C++ Programming

Section: Chapter Questions

Problem 2PP: (Conversion) An object’s polar moment of inertia, J, represents its resistance to twisting. For a...

See similar textbooks

Similar questions

Suppose that a parachutist with linear drag (m=50 kg, c=12.5kg/s) jumps from an airplane flying at an altitude of a kilometer with a horizontal velocity of 220 m/s relative to the ground. a) Write a system of four differential equations for x,y,vx=dx/dt and vy=dy/dt. b) If theinitial horizontal position is defined as x=0, use Euler’s methods with t=0.4 s to compute the jumper’s position over the first 40 s. c) Develop plots of y versus t and y versus x. Use the plot to graphically estimate when and where the jumper would hit the ground if the chute failed to open.
Q2/ The pipe in Fig. is driven by pressurized air in the tank. What is the friction factor (f) when the water flow rate through pipe is ( 85 m/hr ) and the pressure at point 1 is (2500 kPa). (25Marks) 30m smooth pipe d = 70mm open jet P1 1 90m 15m 60m
An aluminum wire having a cross-sectional area equal to 4.60 x 10-6 m? carries a current of 7.50 A. The density of aluminum is 2.70 g/cm³. Assume each aluminum atom supplies one conduction electron per atom. Find the drift speed of the electrons in the wire. 1.95E-4 The equation for the drift velocity includes the number of charge carriers per volume, which in this case is equal to the number of atoms per volume. How do you calculate that if you know the density and the atomic weight of aluminum? mm/s
2. Heat conduction in a square plate Three sides of a rectangular plate (@ = 5 m, b = 4 m) are kept at a temperature of 0 C and one side is kept at a temperature C, as shown in the figure. Determine and plot the ; temperature distribution T(x, y) in the plate. The temperature distribution, T(x, y) in the plate can be determined by solving the two-dimensional heat equation. For the given boundary conditions T(x, y) can be expressed analytically by a Fourier series (Erwin Kreyszig, Advanced Engineering Mathematics, John Wiley and Sons, 1993):
Solve the following equations. Be sure to check the potential solution(s) in the original equation, to see whether it (they) are in the domain. (a) log, (r? –x – 2) = 2
a. For the function and point below, find f'(a). b. Determine an equation of the line tangent to the graph of f at (a,f(a)) for the given value of a. f(x) = 2x°, a = 1 %3D ..... a. f'(a) =
The following is used to model a wave that impacts a concrete wall created by the US Navy speed boat.1. Derive the complete piecewise function of F(t) and F()The concrete wall is 2.8 m long with a cross-section area of 0.05 m2. The force at time equal zero is 200 N. It is also known that the mass is modeled as lumped at the end of 1200 kg and Young’s modulus of 3.6 GPa2. Use *Matlab to simulate and plot the total response of the system at zero initial conditions and t0 = 0.5 s
Find the general solution for the following differential equations:
1. A 500-liter tank initially contains 10 g of salt dissolved in 200 liters of water. Starting at to = 0, water that contains 1/4 g of salt per liter is poured into the tank at the rate of 4 liters/min and the mixture is drained from the tank at the rate of 2 liters/min. Determine the quantity Q(t) of salt in the tank at time t = 0 until the time when the tank overflows. Code a C program which determined this quantity Q(t) by using RK4 method with h = 1. Note: May use the concept of function prototypes, function definition, function call, recursion etc. in a program. 2. A team of surveyors conducted depth-sounding at equidistant locations across the river to measure the area of a river cross-section. Determine the area of the cross-section by coding a C program of the Composite Simpson Rule, taking into consideration the river's 6.0 m width and the fact that it is equally divided into 7 stations. Station Depth, m 0 1 -1.23 24555 3 6 7 -2.08 -2.57 -1.86 -0.65 -0.24 Note: Determine the…
1. Determine the equation of the line through the given point (a) parallel and (b) perpendicular to the given line Given: Point: ( -1,-4) Line: 4x-2y=3
A bicycle wheel has a diameter of 64.6 cm and a mass of 1.87 kg. Assume that the wheel is a hoop with all of the mass concentrated on the outside radius. The bicycle is placed on a stationary stand and a resistive force of 125 N is applied tangent to the rim of the tire. (a) What force must be applied by a chain passing over a 8.96 cm diameter sprocket if the wheel is to attain an acceleration of 4.49 rad/s22? (b) What force is required if the chain shifts to a 5.57 cm diameter sprocket?
Calculate the value of g and h in the following equation.