A 20 mm diameter steel rod passes concentrically through a bronze tube (200+SN) mm long, 50 mm external diameter and 40 mm internal diameter. The ends of the steel rod are threaded and provided with nuts and washers which are adjusted initially so that there is no end play at 25°C.. 1. Assuming that there is no change in the thickness of the washers, if the stress produced in the steel is (200+SN) MN/m2 when one of the nuts is tightened, the pitch of the thread being 1 mm. Find the number of turns for the nut and stress in bronze tube.2. If the temperature of the steel and bronze is then raised to 4O°C find the changes that will occur in the stresses in both materials. The coefficient of linear expansion per C is 10 x10-6 for steel and 17 x10-6 for bronze. E for steel = 210 GN/m2. E %3D for bronze = 100 GN/m2.. Note: SN = %3D %3D Student number =32 Student Number

A 20 mm diameter steel rod passes concentrically through a bronze tube (200+SN) mm long, 50 mm external diameter and 40 mm internal diameter. The ends of the steel rod are threaded and provided with nuts and washers which are adjusted initially so that there is no end play at 25°C.. 1. Assuming that there is no change in the thickness of the washers, if the stress produced in the steel is (200+SN) MN/m2 when one of the nuts is tightened, the pitch of the thread being 1 mm. Find the number of turns for the nut and stress in bronze tube.2. If the temperature of the steel and bronze is then raised to 4O°C find the changes that will occur in the stresses in both materials. The coefficient of linear expansion per C is 10 x10-6 for steel and 17 x10-6 for bronze. E for steel = 210 GN/m2. E %3D for bronze = 100 GN/m2.. Note: SN = %3D %3D Student number =32 Student Number

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a 4ll Asiacell Q2 A 20 mm diameter steel rod passes concentrically through a bronze tube (200+SN) mm long, 50 mm external diameter and 40 mm internal diameter. The ends of the steel rod are threaded and provided with nuts and washers which are adjusted initially so that there is no end play at 25°C. 1. Assuming that there is no change in the thickness of the washers, if the stress produced in the steel is (200+SN) MN/m2 when one of the nuts is tightened, the pitch of the thread being 1 mm. Find the number of turns for the nut and stress in bronze tube.2. If the temperature of the steel and bronze is then raised to 40°C find the changes that will occur in the stresses in both materials. The coefficient of linear expansion per C is 10 x10-6 for steel and 17 x10-6 for bronze. E for steel = 210 GN/m2. E for bronze = 100 GN/m2. Where SN=3 إجابتك
In the hanger shown, the upper portion of link ABC is 3/8 in. thick,and the lower portions are each 1/4 in. thick. Epoxy resin is usedto bond the upper and lower portions together at B. The pin at Ais of 3/4 in. diameter while a 3/8 in. diameter pin is used at C.Determine:(a) the shearing stress in pin A(b) the shearing stress in pin C(c) the largest normal stress in link ABC(d) the average shearing stress on the bonded surfaces at B(e) the bearing stress in the link at C * Letter c, d and e only
The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.
An aluminum alloy cylindrical roller with diameter 1.25 in and length 2 in rolls on the inside of a cast-iron ring having an inside radius of 6 in, which is 2 in thick. Find the maximum contact force F that can be used if the shear stress is not to exceed 4000 psi.
3. A circular steel cylinder of external diameter 0.2 m and internal diameter 0.1 m is shrunk onto a circular aluminium alloy cylinder of external diameter 0.1 m and internal diameter 0.05 m, where the dimensions are nominal. Determine the radial and hoop stresses at the bores and outside surfaces, such that when there is an internal pressure (retained by end caps) of 300 MPa, the maximum hoop stress in the inner cylinder is 150 MPa.
A pipe carrying steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate used to cap the end. How many 40-mm-diameter bolts must be used to hold the cap on if the allowable stress in the bolts is 105 MPa, of which 55 MPa is the initial stress? What circumferential stress is developed in the pipe? Why is it necessary to tighten the bolt initially, and what will happen if the steam pressure should cause the stress in the bolts to be twice the value of the initial stress? *
(1) A steel cylinder (Øyp = 260 MPa) of inner radius a and outer radius 3a is subjected to an internal fluid pressure pi (Note: ratio of wall thickness (t) to inner radius indicates that this is a thick-walled cylinder). (a) Determine (i) the maximum radial stress (ơmax); (ii) the maximum tangential stress (o0max). (b) Determine the limiting values of p, using: (i) the maximum distortion energy theory of failure; and (ii) the maximum shear stress theory of failure. (Hint: Maximum radial and tangential stresses occur at the same radial distance, see slide 8 of Lecture 9 notes); use these maximum stresses as your principal stresses). (c) A steel gun barrel of inner radius 0.6 m is subjected to an internal explosive pressure of 80 MPa. The tensile and compressive elastic strengths of the material are 320 MPa. Assuming a factor of safety of 2, design the wall thickness of the gun barrel.
A flanged bolt coupling consists of eight 10-mm diameter steel bolts on a bolt circle 400 mm in diamater and six 10 mm diamter steel bolts on a concentric circle 300 mm in diameter. When the shear force developed in each bolt in the outer concentric circle is 8000 N, then the stress in each bolt is
echanics of Materials I X t.php Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 1.5 kN. The crankshaft dimensions are b1 = 55 mm, b2 = 150 mm, and b3 = 45 mm. The diameter of the upper shaft is d= 22 mm. Determine the normal stress at point A, which is located on the surface of the upper shaft at the z0 axis. Yo Letferbimtse ENene 302 704 MPal
A link is loaded as shown, it is attached with two bolts with a diameter of 0.25 in. The link width is 2 lh and its thickness is 0.1 in, if the average normal stress in the link is 20 ksi (away from the bolts) determine the applied force G, the shear stress of a bolt as well as the bearing stress in one of the bolt holes. 2 in G
1. (a) Explain briefly why a single-cylinder ('mono cylinder') may be replaced with a force-fitted compound cylinder ('duplex cylinder') with the same inner and outer diameters for a high internal pressure bearing application. (b) An alloy steel cylinder of bore radius (n) 40 mm and outer radius (R) 60 mm is subjected to an external pressure of 30 MNM2. (1) Determine the circumferential stresses generated at the bore and outer surface of the cylinder. (II) Sketch the form of distribution of radial and circumferential stresses across a radius. (c) The cylinder in (b) above is to be used as a hydraulic cylinder. For this application, it needs to be strengthened by shrink fitting onto it a sleeve of outer radius (ro) of 80 mm of the same steel as shown in Figure 1(c). The interference pressure generated due to this fit is 30 MNM2. Observe: This pressure is the same as the external pressure used in the calculations in part (b). (1) Determine the circumferential stress generated in the…
A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5 MPa. The average circumferential (hoop) stress in MPa is