A 2.4 kips The two portions of member AB are glued together along a plane forming an angle 0 with the horizontal. Knowing that the ultimate stress for the glued joint is 2.5 ksi in tension and 1.3 ksi in shear, determine (a) the value of 0 for which the factor of safety of the member is maximum, (b) the corresponding value of the factor of safety. (Hint: Equate the expressions obtained for the factors of safety with respect to the normal and shearing stresses.) 1.25 in. 2.0 in.

A 2.4 kips The two portions of member AB are glued together along a plane forming an angle 0 with the horizontal. Knowing that the ultimate stress for the glued joint is 2.5 ksi in tension and 1.3 ksi in shear, determine (a) the value of 0 for which the factor of safety of the member is maximum, (b) the corresponding value of the factor of safety. (Hint: Equate the expressions obtained for the factors of safety with respect to the normal and shearing stresses.) 1.25 in. 2.0 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

! Required information Consider the given state of stress. A 16 ksi 10 ksi Determine the normal and shearing stresses after the element shown has been rotated through 15° clockwise, using Mohr's circle. The normal stress Ox'is - |ksi and Oy'is ksi. The shearing stress Tx'y'is ksi.
Two steel rods are welded together (see figure);the seam is oriented at angle θ = 50°. The stresses onthe rotated element are σ x1 = 10 ksi, σy1 = -12 ksi,and τx1y1 = -5 ksi. Find the state of plane stress onthe element if it is rotated clockwise to align the x1axis with the longitudinal axis of the rods.
Problem 1 Please choose the correct answer and also write down your solution. (1) The beam is subjected to the shown loading. What is the correct statement regarding the flexural stress at A and B? P P a. Both og and og are tensile stress. 0.5 m 0.5 m 0.5 m b. Both oa and og are compressive stress. Og is tensile stress and og is compressive stress. с. d. OA is compressive stress and og is tensile stress. A В (2) The cantilever beam is subjected to the load P and has cross section as shown. What is the ratio of the magnitudes of the maximum tensile and compressive flexural stresses over the a-a cross section? b. 3/7 a. 7/2 d. 2/10 е. 3/10 h. 10/3 c. 7/3 f. 10/2 i. 1/1 g. 2/7 250 mm 20 mm 60 mm 200 mm 2 m 1 m 15 mm 15 mm
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
The bar ABC is fixed at A and restricted at C by two 16-mm diameter vertical steel bars, 1500 mm long. A 6000 Nm torque is applied at B. Steel has a modulus of elasticity of 200x109 N/m2 and a shear modulus of 80x109 N/m2. Determine: Maximum shear stress at the horizontal bar ABC Tensile Stress at bar MN Note: Draw the Free Body Diagram, Compute for all of the necessary elements, Include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.82 in.² and bar (2) has a cross-sectional area of 0.41 in.². After load P is applied, the strain in bar (1) is found to be 700 μe. Assume L₁=69 in., L₂-89 in., a=34 in., b=33 in., and c-37 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection VD of point D on the rigid bar. (c) the load P. A Answers: (a) 0₁ = (b) VD = (c) P= i i i L₁ a (1) B L2 b ksi, 0₂ = in. kips. (2) C i D P ksi.
3. For the given structure and boundary conditions, what is the allowable load Pallow if the material strengths in shear and tension are T = 200 MPa and o=360 MPa, respectively? The pins carry shear and bars BC and DE carry axial load. Disregard the stress conditions of member ACD, which carries lateral load. All pins are in single-shear and have a diameter of 12mm. Use a factor of safety of 2.0. A ABC = 100mm2 B D C Pallow E ADE = 100mm² 240mm 150mm
Using the methods of consistent deformations, solve the given truss shown and in redundant, use Dy.
Determine (a) the principal stresses and (b) the maximum in- plane shear stress and average normal stress. Specify the orientation of the element in each case. 30 ksi 9 ksi
Rigid bar ABCD is loaded and supported as shown. Steel [E = 30000 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.75 in.2 and bar (2) has a cross-sectional area of 0.425 in.2. After load P is applied, the strain in bar (1) is found to be 780 μs. Assume L₁-60 in., L₂=90 in., a=40 in., b=40 in., and c-30 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vp of point D on the rigid bar. (c) the load P. A Answers: (a) 0₁ = (b) VD= (c) P = i i i L₁ a L2 in. (2) ksi, 0₂ = i kips. C D P ksi.
Determine the normal stress (in Mpa) in member AB of the truss shown if it is made up of a 14-mm-square bar of alloy and the load P is 21.53 kN. Express your answer in two decimal places.
Find the average normal stresses on members AB, BE, and EG, if the area of all members is 1200mm2.