"A 150 kW, 240 V machine-A is in parallel with a 400 kW, 240 V machine-B. The voltage regulation of both machines is 4.5 percent. Machine-A is carrying 300 Amp and machine-B is carrying 600 Amp. What will be the increment increase in load on machine-A and B respectively (in Amp) if an additional 500 Amp load is connected to the bus?" O 136.36 & 363.64 250 & 250 154.32 & 345.68 O None is correct

"A 150 kW, 240 V machine-A is in parallel with a 400 kW, 240 V machine-B. The voltage regulation of both machines is 4.5 percent. Machine-A is carrying 300 Amp and machine-B is carrying 600 Amp. What will be the increment increase in load on machine-A and B respectively (in Amp) if an additional 500 Amp load is connected to the bus?" O 136.36 & 363.64 250 & 250 154.32 & 345.68 O None is correct

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit shown in figure. For the circuit shown in Figure IF IB= 40 MA , VBB= 6v, RE= | Ksr, P= 80o FRc Re VeB Re The value of IE is . . mA..* О 3.24 O 4.24 O 5.24 O 6.24 O 1.24 O 2.024 The value of RB is . Kohm.. * O 52.5 O 55.5 O 47.5 O 57.5 O 25.5 O 48.5 The value of Vce is .. volt. NOTE: USE Rc= 3 Kohm, and Vcc= 15 volt. * O 5.04 O 2.04 1.04 O 4.06 O 4.04 O 3.04 O O O O O ООО О о
"A 100 kW, 250 V machine-A is in parallel with a 300 kW, 250 V machine-B. The voltage regulation of both machines is 4 percent. Machine-A is carrying 200 Amp and machine-B is carrying 500 Amp. What will be the increment increase in load on machine-A and B respectively (in Amp) if an additional 400 Amp load is connected to the bus?" O 100 & 300 O 300 & 800 O 400 & 1200 O None is correct
For the circuit shown in figure below, find the unknown currents. 50 A 12 100 A 20A 10A 20 A
6. Identify the electronic symbol pointed by the line in the given schematic diagram F A TIP2066 with Heat Sink MA 01 Ohm E Sw TIP2055 wih Heat Sink B 10 Amp 50 PN Bridge Rectiter 0.1 Ohm SW LMTar2 we Heat Sink FUSE A FUSE 10A 230 Voit AC 12V Out o Gnd in 0.1 Ohm Sw 470uF 230112V 10A Transformer 47000UF Sov Output 10 uf 12V10A D A В C D F M CnolIL Choclk
32
Q-1: Analyze the circuit of the figure shown to determine the voltages at all nodes and the currents through all branches. Where B-30, VECat =0.2 V, Vge = 0.7 V and assume the transistor is silicon.
2. Calculate the full load voltage drop due to armature reaction. RL(Q) V(V) 42 L(A) 140 48 70 24 35 12 48//24 140//70//35 48//24//12 40.7 39.5 0.288 0.797 0.553 1.58 1.126 3.145 2.34 41.5 40.3 40.1 38.3 39.2 39.6 37 1.928 5.21
A Buck Converter converts 24Vdc to 12Vdc with losses of 70W, and a load of 60Ohms. What is the current drawn from the power supply?
DETERMINE RESISTANCE R.( Need only handwritten solution please otherwise downvote).
Question 3: The buck de-de converter shown down has the following parameters Vs=50 V, D=0.4 L-400 uH, C=100 uF f=20 kHz, R= 20 ohm calculate : (1) the output voltage Vo, current lo ? (2) the Ton and Toff? (3) the rms voltage Vrms and current Irms? (4) Power load Po?
Buck converter is used to _________a) Step down the voltageb) Step up the voltagec) Equalize the voltaged) Step up and step down the voltage
A buck converter has an input current of 24 A while required outņut curent is 6 A. What will be te duty cycle of the converter? [Assume lossless system]