A 14-inch square reinforced concrete column with tied transverse reinforcement is being considered for the gravity load-resisting system of a building. What is the maximum permissible area (in sq. inches) of vertical reinforcing bars in this column knowing that the area of steel is limited to 0.01Ag < As < 0.08Ag? 12.5 sq. inches 15.5 sq. inches 24.5 sq. inches 28.5 sq. inches

A 14-inch square reinforced concrete column with tied transverse reinforcement is being considered for the gravity load-resisting system of a building. What is the maximum permissible area (in sq. inches) of vertical reinforcing bars in this column knowing that the area of steel is limited to 0.01Ag < As < 0.08Ag? 12.5 sq. inches 15.5 sq. inches 24.5 sq. inches 28.5 sq. inches

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam 300 mm wide, 500 mm deep and spans 5 m supports a service super imposed dead load of 6 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
Please give me the correct solutions and answer of this problem in principles of reinforced/prestressed concrete
To calculate the reinforcement ratio p, assume a 7 in. slab with an effective depth of 6.0 in., with No. 6 (No. 19) bars spaced 5.5 in. center to center. Imperial Metric bar Linear Mass Density Nominal diameter Nominal area bar size size (soft) (in) (mm) (in) (mm) No.6 0.167 0.249 0.250 6.35 0.05 32 No. 10 0.375 = % 9.53 0.11 #3 0.376 0.560 %3D 71 #4 No.13 0.668 0.994 0.500 12.7 0.20 129 #5 No.16 1.043 1.552 0.625 % 15.9 0.31 200 #36 No.19 1.502 2.235 0.750 = % 19.1 0.44284 #7 No.22 2.044 3.042 0.875 = % 22.2 0.6087 #38 No.25 2.670 3.973 1.000 = % 25.4 0.79 510 %3D No 29 3.400 5.060 1.128 % 28.7 1.00 645 # 10 No.32 4.303 6.404 1.270 1% 32.3 1.27 819 # 11 No.36 5.313 7.907 1.410 % 35.8 11 1.56 1,006 # 14 No.43 7.650 11.384 1.693 1% 43.0 2.25 1,452 # 18 No.57 13.60 20.239 2.257 1% 57.3 4.00 2,581
Please give me the correct solutions and answer of this problem in principles of reinforced/prestressed concrete
10. A simply supported beam 300 mm wide, 500 mm deep and spans 5.0 m supports a service super imposed dead load of 6 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
Considering the nominal shear stress on concrete is f = 0.83 MPa. Calculate the allowable max spacing for 2-legged 10 mm stirrups? Use simplified calculation for Vc. Beam dimensions are 397 x 754 mm. Effective cover of steel reinforcement = 70 mm fy = 275 MPa Spacing should be in multiples of 10 mm. NOTE: USE STORED VALUES IN YOUR CALCULATION
For the bean shown below, the concrete strength is 5000 psi and the yield strength is 60,000 psi. For the midspan section shown, check if steel yields and compute ØM, and compare it with M. WD = 1.2 kips/ft plus weight of beam WL = 1.5 kips/ft %3D 20.5 in 23 in 3 no. 9 bars 18 ft 11 in.
Hello, please solve the question about reinforced concrete from the sixth and seventh chapters of the third civil stage
Subject: Reinforced Concrete Structures exam
7.b
10
Find the minimum theoretical width and height of a rectangular concrete section that will make the beam failure sufficiently ductile. Given: Two layers of 2-Ø25 mm bottom reinforcements fy=414 MPa f'c=35 MPa stirrup diameter=minimum required clear cover=minimum value for beam vertical clear spacing bet. Iayers=minimum value for beam height-to-width ratio=2.0 Note: Ductile failure occurs in beams when the extreme reinforcement layer is strained to 0.004 or greater.