A 120 cm diameter pipeline conveys oil (s=0.80) under a head of 150 m from the mainland to a nearby island, crossing a river (s=1.03) to a maximum depth of 6 m. If the pipe thickness is 8 mm, determine the stress in the pipewall in kPa. a. 87,354.00 b. 67,568.65 c. 83,742,50 d. 78,567.68

Q: eights was pressed into soft clay in a borehole. The torque was applied and gradually increased to…

A: Using relation :s=TπD2H2+D36

Q: A) Figure (2) shows the velocity distribution for flow of water between two parallel plates.…

A: u=10 (0.01y-y2)1) Value of YCalculating values of y when velocity(u)=00.01y-y2=0y=0.01 m & 0…

Q: Given Sps = 1.7, le = 1.0, and the seismic design forces and weights in the table below find the…

A: Given information,  Sdc = 1.7 Ic = 1.0

Q: A gravity dam has the following dimensions Height of dam Free board=100m, free board = 1m, slope at…

A: Height of the dam = h=  100mFree board = 1mUpstream Slope = 0.15:1αh= 0.1y= 50m

Q: If the tubular shaft has an allowable shear stress of 65MPa, determine the required wall thickness…

A: It is given that : allowable shear stress of 65MPa outer diameter of the shaft is150mm. To Find -…

Q: water flows in a 2am dia. pipe, Calculate the largest discharge upto which flow will be definitely…

A:

Q: A horizontal 45° bend 750 mm Ø upstream and 300 mm Ø downstream has water flowing thru it at the…

A:

Q: Consider the simple pipe network below. Pipe AB and CF are both 500m long with diameters of 0.8m and…

A: LAB = LCF = 500 mL1 = 200 mL2 = 300 mQ = 3 m3/s

Q: plate moves 10 cm/s to the right is 0.5 cm above a stagnant wall. The fluid bet. the plate and the…

A:

Q: Question attached

A: Solution: Capillary risehc=4σCosθγdhere,γw=9810 N/m3σ=Surface tension=0.075 N/md1=0.00075…

Q: determine the stress in the pipe wall in kPa.

A: HOOP STRESS

Q: Find the hydraulic gradient and the head at point C of the following structure for static condition,…

A:

Q: Water flows with a velocity of 6 m/s through the pipe at A. (Figure 1). 300 mm 200 mm 6 m/s

A: Solution: Considering the diagram : Control volume

Q: Question attached

A: The vertical stress can be calculated by using the following relation ∆σA=2qπaaα1+α2+bα1 where, q=γH…

Q: Problem 3. In the figure, a circular opening 1.2 m. in diameter is closed by a hemi- spherical shell…

A: The force required to lift shell vertically is given by Fv ;The FBD is drawn as ;The depth acting…

Q: Q1/ For the hydraulic structures below, Q = 20o0m3/sec, water way = 100m, Pond level = 160m, safe…

A:

Q: Required information When water at 20°C flows through an 20-cm-diameter pipe, the wall shear stress…

A: The flow of air from a region of high pressure to a region of low pressure is caused by the pressure…

Q: In a hydraulically smooth pipe flow, wall shear stress (to) is measured as 1.5 N/m?. Pipe diameter…

A: The FBD of the section is shown below:

Q: A vane, 12 cm long and 8 cm in diameter, was pressed into a soft clay at the bottom of a bore hole.…

A: Given- Length H=12 cm, Diameter D=8 cm, Torque T=45 N-m, It is needed to find the shear strength of…

Q: Determine the wall shearing stress in a pipe of diameter 100mm, which conveys water. The velocities…

A: Diameter of pipe = 100mm Velocity at bottom = umax = 2m/s Velocity at 20mm from the wall of pipe = u…

Q: 12- What is the value of earthquake velocity response spectrum for Tn=0? a) b) c) d) e) Zero ton. 0.…

A: Earthquake velocity also known as seismic velocity.The speed of a seismic wave travels through a…

Q: Hom H.W 01: The figure below shows a section of a hydraulic structure. The structure is founded on…

A: Given data,fig of hydraulic structure is given Bligh's factor of safety=C=6FINDsection is safe or…

Q: with a uniform pressure of 250 kPa. a) Calculate the vertical stress increase at points A (center),…

A:

Q: Compute the uplift force in KN per meter

A:

Q: Q1/ For the hydraulic structures below, Q = 2000m3/sec, water way %3D = 100m, Pond level = 160m,…

A:

Q: Problem #1 Determine the magnitude and the location of the hydrostatic force on the 2 m by 4 m…

A:

Q: 3. Determine the magnitude and location of the total hydrostatic force acting on the 2 x 4 m gate…

A: Given, Area of gate = 2m x 4m

Q: You have a model consisting of 3 layers with seismic velocities v1, v2, v3, and thicknesses h1, h2,…

A: Data Given: Layer = 3 Seismic velocities is layers = V1, V2 and V3 Thickness of the layer = h1,h2…

Q: Problem 6 A 6 meter high, 5 meter wide rectangular plate blocks the end of a 5 meter deep freshwater…

A:

Q: Hydraulics Question is in the Image

A:

Q: 50 2 50 100 SỐ 12

A:

Q: Estimate the Hazen-Williams pipe roughness factor, C, for a 250-millimeter (mm) diameter water main.…

A: To determine the Hazen-Williams pipe roughness factor (C) for given flow parameters.   Given,…

Q: Find the maxeimum ben 75 Nm 60 N/m 5m ØIcm

A: The stress developed in the beam due to the bending action in the beam is called bending stress. The…

Q: foundation soil is 0.45.

A: Given:- Specific weight of concrete = 150 lb/ft3Coefficient of friction between base and foundation…

Q: The canal shown below runs 40 m into the paper. Assume unit weight of H2O is 9.79 kN/ m^3. Determine…

A: Determine the horizontal component of the hydrostatic force against the quarter circle wall

Q: A pipe has a wall thickness of 7.5 cm and under a static head of 70 m of water. What is the diameter…

A:

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.