A 12” pipe contains a short section in which the diameter is gradually reduced to 6” and then enlarged again to 12”. The 6” section is 2 ft below Section A in the 12” where the pressure is 75 psi. If a differential gage containing mercury is attached to the 12” and 6” sections, what is the deflection of the gage when the flow of water is 4.25 cfs downward? Draw the figure

Q: Date No. A diffevential manometer is connected at two puints A and B of two pipes as Shown on the…

A:

Q: V. 10-) % of bouy above the liquid surface %3D (-) X100 :: above thu liguid Volume above liguid = V-…

A:

Q: Air at 30 °C is flowing in a 2.75-mm-diameter tube at such a rate that the wall shear stress has a…

A:

Q: A B 3. Pipe no. Diameter (mm) Length (m) Friction factor Q (1/s) 1 75 120 0.018 15 l/s 2 100 150…

A:

Q: A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C- 80…

A: \We have formulaH=10.583LQ1.85C1.85d4.87Q=150lps=0.15m3sL=1km=1000md=0.4m

Q: 1. 'Water flows through a 12 inches by 6 inches venturi meter at the rate of 1.49 ft/s and the…

A:

Q: Question 19 A pipe connected in series has the following roughness or friction coefficients: Pipe 1…

A:

Q: Derive a formula for capillary rise (h) between two concentric glass tubes of radiuses R1 and R2,…

A: Answer  To derive the capillary rise formula consider the forces acting on the water due to surface…

Q: 14.5 A differential gauge was attached to a inches. Assume no headloss. Point B is located at the 6…

A: From the given question it is required to calculate the flow rate in ft3/s.

Q: For the pipe network shown below, estimate the diameter of pipe DE, knowing that the flow at A = 200…

A: Data given Find : Diameter of pipe ED

Q: Probl Compute gage pressure at the center of pipe. For solution use: (a)British Unit, (b)Standard…

A: To Determine Gauge pressure in the centre of the pipe. a) In British unit ( psi ) b) In SI unit (…

Q: Two vats are connected by a submerged pipe with a square cross-section, as shown in Figure Q2. A…

A: h2 > h1 Let density of fluid be ρ

Q: Q1: The figure below shows a regulator, determine whether the structure is safe against piping or…

A: Determine whether the structure is safe against piping or not and design the thickness of floor by…

Q: Prob-8 A venture tube, fabricated with a machined entrance cone is inserted in a 4 in. inside…

A:

Q: L For the figure shown, determine the elevation at c. Use Darcy-Weisbach formula to compute for the…

A:

Q: During a gauge field check you notice the pressure drops rapidly using the Red tube. This does not…

A: Pressure drop:- The difference in total pressure between two places on a fluid-carrying network is…

Q: Which of the following pressure-tap arrangements will yield the lowest pressure drop reading for an…

A: Orifice pressure tap positions are defined by a number of standards. The upstream pressure tap…

Q: A horizontal pipe has two sections with diameters 5'7" and 1'1" respectively with a smooth…

A:

Q: This is not an assignment question

A: GIVEN- γ1=10KN/m3γ2=20KN/m3H1=50cm=0.5mH2=10 cm =0.1mPB=?

Q: Q2: Find the diameter of the pipe 2 in the loop shown below which contains two pipes connected in…

A: ##Calculation of diameter of Pipe 2 using hazen Williams equation

Q: A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 120…

A:

Q: sticity and dimensions of a at the celerity of pressure wav ne pipe diameter is 1.2 m. and d 600 m.…

A: celerity of oressure wave , c =975m/sDiameter of pipe , d = 1.2 m length of pipe , l= 600 m velocity…

Q: 150mm dia. 300mm dia. 800 mm Water Mercury (SG = 13.6) A vertical venturi meter 150mm diameter is…

A: Discharge can be calculated by ; Q=A1A2A12 - A222gh A1 = π4(D1)2 =  π4(0.3)2  = 0.071m2 A1 = π4(D2)2…

Q: A pipe has a uniform diameter of 750 mm. The flow rate entering the pipe is 2.21 m^3/s. The exit…

A:

Q: A 50 °C of liquid water is flowing into and discharging from a pipe U-section as shown in Figure 1.…

A: Velocity defines how fast the air is moving in distance per unit of time. The common units are…

Q: Compute the meter coefficient, Cd.

A:

Q: Problem II. Frictionless, incompressible, one dimensional flow of the water passes through the…

A: Given,

Q: The discharge through a 180° bend of 50-cm dimeter is 2.5 m/sec. If the pressure at section 1 equals…

A:

Q: he proper-sized steel tube for a flow rate of 20 gpm and an operating pressure of 1.000 psi. The…

A: Solution-  Data given   flow rate = 20 gpm operating pressure = 1000 psi    velocity = 20 ft/s…

Q: .... 2.5 ft/s dyx.... 10 ft/s Not to scale L A 3 feet long nozzle is attached to a pipe having a…

A:

Q: 4m Oil (0.90) 3.75 mm Mercury (13.57) This vertical pipeline with attached gage and manometer…

A: Given data in question  Vertical pipe Specific gravity  Mercury To find out  Pressure at A in bars

Q: Determine the discharge through the three new cast iron pipes connected in series having diameters…

A:

Q: 1.0 ft /s of water flows through 100 ft of 6 in steel pipe at a temperature of 70 degrees F. The…

A: Given, Q=1 ft3/s L=100 ft of 6 in T=70°F rd=20ν=0.739×10-5 Diameter= 6 in=0.5 ft

Q: Calculate the coefficient of discharge for the venturi meter if the flow rate is 102 m^3/hr. O 0.197…

A:

Q: a) Please find the pressure difference between A and B (PA-PB or P₁-P₁ 7 b) Please calculate the…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?