Water flows through a horizontal branching pipe as shown at a rate of 280L/s. All points are inside the pipe. Determine Pressure (kPa) at point 3 A-0.007m2 P2 35kPa 4. 3 A-0.1m? Q1- 280L/s P- 70kPa A=0.02m2 V3-6m/s O 59.29 25.59 55.92

Q: What is adsorption zone?

A: The deposition of molecular species onto the surface of any object is known as adsorption. The…

Q: What is a plumbing tape?

A: Let us analyse the question ( Plumbing tape ) in step 2.

Q: List several locations where flashing is required?

A: flashing  - flashing use as a obstacle for water penetration. it is thin impervious layer on the…

Q: Which one of the following is the most economical store design? a. Geometrical layout b. Angular…

A: the correct answer is option c - straight floor layout

Q: Dry Flash Column Chromatography ? Please explain at your own words.

A: The process of separation of mixture is known as chromatography. Chromatography is a laboratory…

Q: Draw and label the standard symbols used in a horizontal stadia sight. Define each symbol used.

A:

Q: Define bentonite.

A: Bentonite is a form of clay. It consists of montmorillonite mineral

Q: What is Universal Transverse Mercator (UTM)?

A: A Universal Transverse Mercator is method to represent the three dimensional earth into two…

Q: Define emission factor?

A: Emission Factor An emission factor is a representative value that attempts to relate the quantity of…

Q: SANITARY SEWER SYSTEM

A: To draw the city sanitary sewer system

Q: Illustrate a simple drawing plan of pipeline

A: Simple drawing plan of pipeline: The piping plan or general arrangement drawings show all major…

Q: Where are fire flame detectors used?

A: Answer Introduction Fir flame detector is the sensor that is used to detect the fire flame in any…

Q: What is pole placement method

A: Answer:- The pole placement approach is a very useful design tool, particularly for estimating the…

Q: Asap Find External indeterminacy

A:

Q: Define two-way flat plate.

A: Solution: A flat plate is generally a two-way system that is supported directly on columns or…

Q: How hydrophilic self cleaning surface work？

A: Answer :- Water will spread entirely across the superhydrophilic surface, generating a very thin…

Q: Define electrical profiling method.

A: The electrical profiling method is defined as it is a DC resistivity survey which proposes to trace…

Q: Civil Engineering How does prefabrication contribute to construction operations? (For BIM) Ple

A: Introduction- Building design and construction management are increasingly relying on prefabrication…

Q: Assignment #5: 1. Locate the centroid of the shaded area as shown below. 12 6 6"

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: What are canopy restrictions?

A: Canopy:

Q: How many satellites in a full GPS constellation? O 30 O 12 O24 O 18

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Flowchart of how to estimate EARTHQUAKE LOADS. Please write it down, don't use the book nscp.…

A: Analysis of past earthquakes aids in understanding their causes and mechanisms and may even aid in…

Q: Q#11: Define the following terms: i. Elevation ii. Bench Mark iii. Back Sight iv. Fore Sight v.…

A:

Q: Define Vacuum Dewatering.

A: The method of vacuum dewatering effectively enhances concrete strength , durability and other…

Q: How does a plumbing contractor know what slope is required on sanitary piping installations?

A: The slope changes as the temperature changes in a sanitary installation.

Q: Define Horizontal Drainage.

A: Horizontal drainage is a helpful strategy for consolidating soils which are weakened by water…

Q: 2. Explain the difference between the TRIM default option and TRIM double enter. O Enter your answer

A: Trim default: This tool is simple to use. We need to just select the object which needs to be…

Q: top view drawing

A: In top view we see the object from top. Here dotted line represents a cut inside the object.

Q: Please write a report about (Setting out Right angles) by using tape. Introduction Procedure Aim…

A: Setting out Right Angles: Introduction: While setting out a building plan, it is usually made up of…

Q: 134 438 124 295 408 139 What is the correct phasing design for the 87 318 163

A: Given a four-legged intersection as shown below Required: To choose correct phasing design from the…

Q: Why chaining pins should be set perpendicular to the taped line?

A: The chaining pins should be set perpendicular to the taped line to avoid the errors in the…

Q: A restroom should be located within 400 feet of every permanent workstation

A: Maximum distance is 400 feets ... Maximum of above or below 1 floor in case of building..

Q: installed in the front lawn and along one side and seeded the remain- der with 3.5 pounds per 1,000…

A:

Q: List some benefits of using hand-level instruments.

A: A hand level instrument is a device which is used  for rough levelling.  It is mainly used for small…

Q: " SANITARY PLANNING LAYOUT " A.   FLOOR PLAN - ONE -STOREY RESIDENTIAL BUILDING B.   PLUMBING…

A: A building's or structure's layout depicts the design of its foundation on the ground surface, as…

Q: Which shortcut key lets you zoom the drawing area?

A: Of the given options, the shortcut key to zoom the drawing area in AutoCAD has to be found out

Q: Describe boring spacing and depth?

A: The boring is done for the following purposes- Soil Investigation Determining the depth at which…

Q: quality management plan of Lrt eglinton midtown crossover construction project. 500 words

A: here is your answer below ;

Q: Describe in detail a typical layout of an escalator systems

A:

Q: hat is volume anaylsis system?

A: Civil engineering is mainly concerned with the planning and detailing of the structure. So for the…

Q: Change in the existing use or occupancy without Certificate of Change of Occupancy/Use/Operation.…

A: Brief about the change in the existing use or occupancy without a Certificate of Change of…

Q: Where is the top view?

A:

Q: 27' 30 Find the centro id and mark/draw on the figure with with complete solution 241 K X 24 15 851…

A:

Q: From this plan view,which one is the length and which one is the width and please justify your…

A: The length shows the longer side of the figure, while the width shows how broad or wide it is.…