A 10 kg block A rests on a smooth surface and the spring is compressed 0.1 m. It is attached to an inextensible cord over frictionless, weightless pulleys with a mass B of 24 kg, as shown. If the system is released from rest and B travels 0.1 m, what is A's speed? Consider K = 490N/m (spring) and VA = 2 x VB

A 10 kg block A rests on a smooth surface and the spring is compressed 0.1 m. It is attached to an inextensible cord over frictionless, weightless pulleys with a mass B of 24 kg, as shown. If the system is released from rest and B travels 0.1 m, what is A's speed? Consider K = 490N/m (spring) and VA = 2 x VB

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter9: Refrigerant And Oil Chemistry And Management-recovery, Recycling,

Section: Chapter Questions

Problem 7RQ: Explain what a global warming potential (GWP) is.

See similar textbooks

Similar questions

The end A of the cord is pulled down with a velocity of VA = 7 m/s. At the instant shown, determine: 1. The angular velocity of the spool 2. The magnitude of the velocity of point C located on the outer rim of the spool. 250 mm B 500 mm Select one: O A. w = 12 rad/s and Vc = 6.71 m/s O B. w = 8 rad/s and Ve= 4,47 m/s 1:08 PM A D ) ENG 4/17/2021 人

مقاومه HW2
For a sprak ignition engine the following readings were observed. cylinder diameter 10 cm, stroke length 10 cm and clearance gap between TDC and cylinder head is 10 mm. for such engine the compression ratio will be а. 11 O b. 10 c. 100 d. 110
1 a) The hot combustion gases of a furnace are separated from the ambient air and its surroundings, which are at 25°C, by a brick wall 0.15 m thick (Figure la). The brick has a thermal conductivity of 1.2 W/m K and a surface emissivity of 0.8. Under steady-state conditions an outer surface temperature of 100°C is measured. Free convection heat transfer to the air adjoining the surface is characterized by a convection coefficient ofh = 20 W/m².K. What is the brick inner surface temperature? b) Consider steady-state conditions for one-dimensional conduction in a plane wall having a thermal conductivity k = 50 W/mk and a thickness L = 0.25 m, with no internal heat generation. Determine i) the heat flux and the unknown quantity for each case; and ii) sketch the temperature distribution, indicating the direction of the heat flux. Case T:(°C) T2(°C) dT/dx (K/m) ġ(W/m²) 1 50 -20 70 160 3 40 -80
Which of the following is the right .4 ?one Twb = Tdb Twb = 1/2 Tdb O %3D Twb s Tdb Twb > Tdb O 8
ans: 0.01925kg, 0.7123kg, 1.886kPa Use gas laws
HW problem help
2. Common Fluids Conversions - Please calculate the following: a. 50 GPM to ft/s in a 4" Sch 40 pipe b. 15 GPM to lbm/s of Chloroform at 25°C 30 psi to ft lb-/lbm of Water at 50°C 40 ft lbf/lbm to hp of a fluid moving at 150 lbm/min. Reynolds number for 100% Glycerol at 75°C flowing through a 2.5" Sch 80 pipe at 10 lbm/s d. e.
4 Which of the following could not be the power coefficient of a slow speed wind turbine? a. 0.444 b. 0.3396 c. 0.327 d. 0.265
What is the engine bore (in mm) required for good volumetric efficiency for an engine with one inlet and one exhaust valve, stroke of 90 mm, inlet air temperature of 330 K, engine speed of 8200 rpm and inlet valve diameter 52 mm. Assume specific heat ratio =1.33, R = 287 J/kg.K and an average inlet flow coefficient 0.4. Select one: O a. 86.57 O b. 105.2 O c. 80.23 O d. 89.05 O e. 96.76
Power plant.
What is the engine speed (in rpm) required for good volumetric efficiency for a square engine with one inlet and one exhaust valve, bore of 0.086 m, inlet air temperature of 327 K, exhaust temperature of 875 K and exhaust valve diameter 31.9 mm. Assume specific heat ratio =1.32, R = 287 J/kg.K, an average inlet flow coefficient 0.37 and an average exhaust flow coefficient 0.47. Select one: a. 7150 b. 7800 c. 5620 d. 8640 e. 9200