98) What is another name for austenitic stainless steels? A) p91 steels B) 18-8 steels C) p92 steels D) o1 steels E) h11 steels 99) which is more important for assembly than its values? A) yield strength B) hardness C) size D) elastic modulus E) wear behavior 100) which is not one of the general properties shown by almost every metal? A) satiety B) high hardness and strength C) good wear resistance D) good thermal conductivity E) good electrical conductivity

98) What is another name for austenitic stainless steels? A) p91 steels B) 18-8 steels C) p92 steels D) o1 steels E) h11 steels 99) which is more important for assembly than its values? A) yield strength B) hardness C) size D) elastic modulus E) wear behavior 100) which is not one of the general properties shown by almost every metal? A) satiety B) high hardness and strength C) good wear resistance D) good thermal conductivity E) good electrical conductivity

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter8: Engineering Materials

Section: Chapter Questions

Problem 15ETSQ

See similar textbooks

Similar questions

A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa Allowable compressive stress 140 MPa 70 MPa If the allowable strain for both materials is 0.0005, which of the following most nearly gives the maximum load the member can carry so that this allowable strain is not exceeded? Select the correct response 162.00 kN 185.00 kN 205.00 kN 175.00 kN
A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa ents Allowable compressive stress 140 MPa 70 MPa ces ents Which of the following most nearly gives the load, in percent, carried by the copper? ssors Select the correct response ication 44.44% Niki 55.56% Blogs 66.67% 33.33% Courses
A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa Allowable compressive stress 140 MPa 70 MPa Which of the following most nearly gives the load, in percent, carried by the copper? Select the correct response: 44.44% 55.56% 66.67% O33.33%
i need quickly please please please Which of these cast iron would allow the greatest amount of plastic deformation before fracture . Nodular cast iron Grey cast iron White cast iron None of them can be worked. If the diameter of steel specimen stretched by tension load is doubled , then it’s tensile strength will be Halved Remain unaffected Doubled Become four times Temperature is proportional with Percent of elongation Tensile strength Modulus of elasticity All above The tensile strength of a steel specimen that have a 182 HB , equals to 490 MPa 910 MPa 627 MPa Not given…
d) No increase Which of the following is not a property of steel materials? C a) Homogeneous and isotropic b) Linearly elastic stress-strain behavior c) Recyclable d) Fire-resistant
Task (3) you are asked to perform tensile test on specimens of two different materials (A and B) and you obtained the stress-strain diagram of the two specimens as shown in Figure 2: 400 350 300 250 Material A 200 150 100 50 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.18 Strain (mm/mm) 50 Material B 30 20 10 0.02 0.04 0.06 0.08 0.1 Strain (mm/mm) Figure 2: Tensile Test Analysis Stress (MPa) Stress (MPa)
Decode the characteristics of a 6063 T831 aluminum.
List the specifying organization for the following types of steel:a. Cold-formed steelb. Hot-rolled steel
Determine the ductility of the following steel samples that undergo tensile strength test. All dimensions in millimeter.
c). Interpret the following diagram? The effect of carbon and heat treatment on the properties of plain carbon steels. 160 140 Tensile 120 strength 100 Impact energy | 100 Annealed 80 80 Normalized 60 60 Annealed 40 `Yield strength 20-% Elongation Annealed 20 Normalized- 0.2 0.4 0.6 0.8 1.0 Weight percent carbon Figure-4 Yield and tensile strength (ksi) Normalized % Elongation or impact energy (ft • Ib)
38. What grade of steel is preferred for the fabrication of most structural shapes other than W-shapes, and what are its yield stress and tensile stress? (Hint: See Figure 3.10.) 9.
Explain the figure below (classification of steel)