Situation 1. The flow rate of water through the pipe system shown in the figure is 45 L/s under total head loss of 8.5 m. Assume C 120 for all pipes. LINE A 300 m, 200 mm LINE B 266 m, 160 mm A. 2.63 B. 2.85 LINE C 190 m 18. Calculate the flow through Line B in L/s. A. 18.4 C. 22.1 B. 20.7 D. 24.6 11. Calculate the head loss in Line B in meters. C. 3.04 D. 3.39 12. Determine the diameter of Line C in mm. A. 140 B. 150 C. D. 160 170 LINE D 510 m, 250 mm

Situation 1. The flow rate of water through the pipe system shown in the figure is 45 L/s under total head loss of 8.5 m. Assume C 120 for all pipes. LINE A 300 m, 200 mm LINE B 266 m, 160 mm A. 2.63 B. 2.85 LINE C 190 m 18. Calculate the flow through Line B in L/s. A. 18.4 C. 22.1 B. 20.7 D. 24.6 11. Calculate the head loss in Line B in meters. C. 3.04 D. 3.39 12. Determine the diameter of Line C in mm. A. 140 B. 150 C. D. 160 170 LINE D 510 m, 250 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 7 - 66 Determine the flow in each of the pipes shown in the figure. Assume f 0.02 for all pipes. El. 90 m El. 75 m B El. 50 m El, 30 m D. Line 3: 45um - 300mm Line 4: 900m - 150mm Line 1: 600m - 600mm Line 2: 300m - 200mm C.
Water is flowing at the rate of 300 L/sec from A to E as shown. Assume f = 0.025 for all pipes. Q2 1500m-300mm A B Q3 C D E 300m-450mm 600m-250mm 600m-300mm 400m-450mm Q4 600m-200m Compute the flow in Pipe 1, Q1 [in m³/s]. O 0.3000 m3/s O 0.1006 m3/s O 0.1418 m3/s O none of these O 0.0576 m3/s O 0.1582 m3/s
Situation 1: A pump draws water from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe and the head loss from 2 to B is twenty-five times the velocity head in the 100-mm diameter pipe. The discharge in the pipe is 20 liters/second. EI. 240m B El. Om 100mm A O 150mm El. -20m 2. Find the power delivered by the pump in kW. 3. Calculate the pressure head at point 1 in meters. 4. Solve the pressure head at point 2 in meters.
Water is flowing at the rate of 300 L/sec from A to E as shown. Assume f = 0.025 for all pipes. 1500m-300mm A Qi В Qs D Q6 E 600m-300mm (6) 400m-450mm 300m-450mm 600m-250mm Q4 600m-200m Compute the flow in Pipe 5, Q5 [in m³/s]. none of these O 0.3000 m3/s O 0.1006 m3/s O 0.1582 m3/s O 0.1418 m3/s O 0.0576 m3/s
What is the difference between the pressure at the two sections? * :A horizontal pipe , I P4 in diameter, taperv gradually to 8 in. in dia meter. If the flow ir 500 cu f4 of water per minute, what i the difference between the presure at the two sections? Given : Quyo ® 500 ft³/min do 8" O 445.66 psf O 417.65 psf O 455.89 psf O 420.11 psf O 432.37 psf
The pipe flow in the figure is driven by pressurized air in the tank. Assuming f = 0.014 and the flow rate is 17.36 liters/sec. Find 20m-1 50mm 10m Find the head loss pipe gage pressure needed to provide the cuid water a Towirste 2132786 liters bec P open jet 100m 40m 8.84 2673.06 178.5 856.25 2157.3 3.58 210.2 OOOO оооо 382.2 73.5
Determine the flow in each of the pipes shown in the figure. Assume f= 0.02 for all pipes. Problem 7-66 El. 90 m A El. 75 m B. El, 50 m El. 30 m D Line 3: 45um - 300mm Line 4: 900m - 150mm 600m - 600mm Line 1: Line 2: 300m - 200mm
Fluid Flow in Pipes 2. The flow from pipelines A to F is 300 lit/s. Using a friction factor of 0.015 for all pipelines and with the properties listed below, compute a. the discharge at B b. the discharge at E c. the discharge at D d. headloss from 1 to 5 Pipelines A TEOREY B C D F Length (m) 350 300 320 1100 550 650 Diameter (cm) 40 25 25 30 20 45
Q5: As shown in figure (5). What is the water horsepower of the pump? The pipes characteristics are as follows. Pipe 1 2 3 EL.0.0m D (mm) 200 300 250 L (m) 900 300 1500 0.135 m²/sec f 0.023 0.018 0.02 EL 120m EL.30m
A 750mm dia. pipe 1162m long carrying 2.4 cubic meter per second of water branches into two pipes, 450mm dia. and 600mm dia. at junction A. The 450mm pipe is 1254m long and the 600mm is 1196m long. They come together at junction B and continue as a single pipe 750mm in diameter and 866m long. Assuming the values of fare 0.017, 0.019, and 0.020 respectively for the 750mm, 600mm, and 450mm pipes. What is the discharge in the 450mm pipe?
water is flowing through a 35cm diameter welded steel pipe (f=0.014) of length 2300m that drains a reservoir under a head of 50m. the pipe has a thickness of 9mm. if the valve at the end of the pipe is closed in 9s. approximately what water-hammer a. 1.667MPa b. 1.567 MPa c. 1.467 MPa d. 1.367Mpa
200mmø 690mm 300 mm 400 mmø 金Ho0 Z Hg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm.