935are 2500 conductors lap-connected and the full-load copper losses are 25 kW? Calculate the area of the poleshoe if the gap density has a uniform value of 0.9 wb/m2 and find the no-load terminal voltage, neglecting15. A 1500 kW, 550-V, 16 pole generator runs at 150 rev. per min. What must be the useful flux if therearmature reaction and change in speed.(Rajiv Gandhi Techn. Univ., Bhopal, 2000) [0.09944 m2, 559 17

In this question dc generator is given....We have to find out no load terminal voltage and area of…

935 shoe if the gap density has a uniform value of 0.9 wb/m2 and find the no-load terminal voltage, neglecting are 2500 conductors lap-connected and the full-load copper losses are 25 kW? Calculate the area of the pole 15. A 1500 kW. 550-V, 16 pole generator runs at 150 rev. per min. What must be the useful flux if there anmature reaction and change in speed. (Rajiv Gandhi Techn. Univ., Bhopal, 2000) [0.09944 m? F

935 shoe if the gap density has a uniform value of 0.9 wb/m2 and find the no-load terminal voltage, neglecting are 2500 conductors lap-connected and the full-load copper losses are 25 kW? Calculate the area of the pole 15. A 1500 kW. 550-V, 16 pole generator runs at 150 rev. per min. What must be the useful flux if there anmature reaction and change in speed. (Rajiv Gandhi Techn. Univ., Bhopal, 2000) [0.09944 m? F

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Alternator voltage regulation is ............... % *
Note: Please write and answer neatly with solutions, thank you!
4. The portion of the flux that goes through one of the transformer coils but not the other one is called. A) Average flux C) Total flux B) Mutual flux D) Leakage flux 5. The ------- are represented in the induction motor equivalent circuit by the resistor Rc (or the conductance Gc). A) Stray losses. C) Air-gap losses B) Friction and windage losses D) Core losses 6. The per-phase voltage Vo can be calculated by dividing the total voltage on. A) √3 B) √1.404. C) √0.707. D) √2.
4. The portion of the flux that goes through one of the transformer coils but not the other one is called. A) Average flux B) Mutual flux D) Leakage flux C) Total flux 5. The fundamental component of the magnetization current ------- the voltage applied to the core by ------ 90°: A) Lags, 45° B) Leads, 45°. D). Leads, 90°. C) Lags, 90°. 6. The ----- are resistive heating losses in the core of the transformer. A) Hysteresis losses. B) Copper losses. C) Leakage flux losses. D) Eddy current losses. 7. The total rotational losses of an induction motor are a combination of: A) Friction losses B) Windage losses. C) Core losses. D) Stray losses. 8. Induction motors are now the preferred A) absence of brushes. choice for industrial motors due to B) Small size. C) Less control requirements. D) rugged construction. 9. For an induction motor, if the synchronous speed is 1800 r/m, and the rotor speed 180rad/sec, then the slip will be: A) 5.5 % C) 6% B) 4.5% D) 4% 10. The lower the speed of an…
A 2 pole wave wound dc generator has 44 slots, each slot having 20 conductors. The flux/pole is 0.018 weber. At what speed the armature be rotated to get an induced emf of 220 V. What will be the induced emf developed if the armature winding is lap connected and runs at the same speed. Speed Generated Emf when lap connected
50 KW, 240 V enduvi resistance of a generator with foreign excitation is 0.02 ohms. Generatorproduces rated voltage at rated load. Endüvi voltage and endüvi current at rated loadcalculate? If the output voltage is kept constant at 240V and the output power is reduced to 45 KWfind the enduvi tension necessary for this?
5
A 6 pole generator with wave wound armature has 58 slots each having 20 conductors. The flux per pole is 0.01 Wb. () At what speed must the armature rotate to give an induced EMF of 230V is, GD What will be the voltage developed, if the winding is lap connected and the armature rotates at the same speed is,
The shunt field winding of a shunt generator has a resistance of 80ohms at 20 degrees Celsius. After several hours of continuous operation, the winding temperature rises to 50 degrees Celsius. How much is the winding resistance under this condition. Assume the resistance temperature coefficient of copper to be 0.004 ohm per degree at 0 degree Celsius. *
There are 175 slots in a 3-phase, 16-pole, 50 Hz., star connected alternator. There are 4 conductors in each slot and all the conductors in a phase are connected in series. Coil span is 130° electrical and the flux per pole is 0.04 Weber sinusoidallly distributed. Calculate the emf induced per phase.