80 160 150 140 130 120 110 100 90 OSI or oRI 02I O1 t 001 04 10 20 30 40 50 60 50 40 30 20 i0 Force 210 220 230 240 250 260 270 20 290 300 310 320 330 330 320 31O 300 290 280 270 260 250 240 230 220 210 Table eisco 091

Q: Determine the diameter (in mm) of the largest circular hole that can be punched into a sheet of…

A: Have a look

Q: Assume the breaking stress of a bone is 1.30 x 107 N/m2, the magnitude of the maximum force a…

A: Given Breaking stress of a bone =1.30x107Nm2 Average diameter of bone =d= 3cm Area of bone=πd24…

Q: ) Unit of Young's modulus is: Select one: a. N/m O b. N/m? Oc. N.m2 O d. N

A:

Q: relat A climber exerts a force of 900N on a rope during an unexpected fall. Use the information…

A:

Q: When using the Method of Sections, if I cut through a member and I assume that the member was in…

A: When using the Method of Sections, if I cut through a member.

Q: Advanced Physics There is a 4-story building destined for Housing, projected in the city of Lima…

A: Solution:-              (a).   Determine the Fundamental  period:               The seismic load is…

Q: 6) Multiple choice: What is the AISC recommended slenderness ratio limit for tension members? a)…

A:

Q: Solve step by step in digital format с oos A 5000 kg B Find the stresses in the cables VAC = = =…

A:

Q: 3. Consider a load of mass 120.0 kg that is being held up by two tensioned cables. Cable 1, with…

A:

Q: 45 20 T2 |Tэ

A: Consider the given diagram.

Q: Stress is the quantity that contains information about the magnitude of force causing deformation,…

A: Stress = Restoring force / area

Q: Q.3) Trusses are designed to carry: (a) axial load (c) torque (E) No one of above write your answer…

A: Answer             A) axial load

Q: A circular tank of 3.91m in diameter is uniformly loaded with 100 kPa. Compute: a) The stresses…

A:

Q: The coefficients of static and kinetic friction between the 50-kg crate and the ground shown in…

A:

Q: 3. Using the Method of Sections determine the load in members BD, CD, and CE.

A:

Q: Ex. 14: The frame of brass plate of an outer door design has 1.60 m square and thickness 1 cm. the…

A:

Q: 2-47. Determine the magnitude and orientation, measured counterclockwise from the positive y axis,…

A: Resultant of two vector can be determined using parallelogram law of vector.

Q: السؤال 3 The component of stress tensor perpendicular to the plane are called normal stresses 0 صواب…

A: Required :: True or False

Q: What is an unsafe practice when setting up climbing anchor? Put equal load on each anchor point Be…

A: Climbing is done with good equipment and with proper planning to reduce the tendering of the…

Q: Several studies indicate that the elastic properties of tendons can change in response to exercise.…

A: A) The force constant is the slope of the force versus deformation curve. Determine the force…

Q: Use the information for the fibula(Y-17.9GPA) in Figure to: (a) Caleulate the maximum tension a bone…

A: (a) Write the formula for the maximum stress the Fibula bone can withstand before fracture.…

Q: Which of the following are SI units of Young's modulus? (There could be more than one correct…

A:

Q: What pressure is required to reduce the volume of a lead block by 1% ? (Given : Bulk modulus of lead…

A: Description : In this question we have to find the pressure required to reduce the volume of lead by…

Q: What is the tension of individual cords A,B,C in terms of lamp weight(w)?

A: (a) Resolve the tension forces acting along x axis on the individual cord A. Resolve the tension…

Q: Q4) A force of magnitude F = 62 × 10° N is applied perpendicularly to the steel rod of radius 9.5 mm…

A: Given data The magnitude of the force is F = 62 x 103 N The rod's radius is r = 9.5 mm. The length…

Q: A liquid compressed in a cylinder has a volume of 1000 cm³ at 2MN/m² and a volume of 993 cm³ at 3.3…

A: Given: A liquid compressed in a cylinder has, Volume of 1000 cm3 at 2 MN/m2 Volume of 993 cm3 at 3.3…

Q: Situation 2. Determine the maximum weight of the bucket that the wire can support so that no single…

A: The maximum tension in the wire is given as, T=100 lb. DIAGRAM: TO DETERMINE: The maximum weight of…

Q: Calculate the force (in N) a piano tuner applies to stretch a steel piano wire 8.2 mm if the wire is…

A: The solution for this question has been solved below..

Q: At the back of the leg, two muscles pull on the Achilles tendon to create an upward force. Estimate…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A vertebra is subjected to a shearing force of 497 N. Find the shear deformation, taking the…

A: Given:Shear force = 497 NHeight of cylinder = 3.2 cm = 0.032 mRadius of cylinder =…

Q: Which of the following represents volumetric strain? a) -ΔV/V b) ΔV/V c) Pressure/Volume d) -P /…

A: To find: Which of the following represents volumetric strain

Q: Type of strain with a symbol of epsilon * O Linear O Shear Volume (Bulk) O Strain

A:

Q: d) A cylindrical rod 100 mm long and having a diameter of 10 mm is to be defomed using a tensile…

A: According to the following question,  this question ask us that, we have to examine the four alloys…

Q: The mass of the block = 269 kg %3D First Force applied, Fapp 1 = 187 N Second Force applied, Fapp 2…

A:

Q: coefficient of viscosity is equal to the ratio of shear stress to shear strain. True or False? a)…

A: True or False: Coefficient of viscosity is equal to the ratio of shear stress to shear strain.

Q: The mass of the block 106 kg First Force applied, Fapp 1 = 249 N %3D Second Force applied, Fapp 2 =…

A:

Q: After an unfortunate accident occurred at a local warehouse, you were contracted to determine the…

A:

Newton's First Law of Motion

If a very smooth ball is rolled down an inclined surface with zero friction, the ball will continue to roll indefinitely for an infinite time, in an attempt to reach to the same height on the opposite hill!