8. For a bronze alloy with a cross-sectional area of 300 mm² and a modulus of elasticity of 120 GPa, the maximum stress that can be carried by the alloy without plastic deformation is 300 MPa. If the original specimen length is 95 mm, what is the maximum length to which it may be elastically stretched? (a) 0.24 mm (b) 95.24 mm (c) 237.50 mm (d) 332.50 mm

8. For a bronze alloy with a cross-sectional area of 300 mm² and a modulus of elasticity of 120 GPa, the maximum stress that can be carried by the alloy without plastic deformation is 300 MPa. If the original specimen length is 95 mm, what is the maximum length to which it may be elastically stretched? (a) 0.24 mm (b) 95.24 mm (c) 237.50 mm (d) 332.50 mm

Chemistry for Engineering Students

3rd Edition

ISBN:9781285199023

Author:Lawrence S. Brown, Tom Holme

Publisher:Lawrence S. Brown, Tom Holme

Chapter1: Introduction To Chemistry

Section: Chapter Questions

Problem 1.82PAE: Use the web to research the elastic modulus and yield strength of carbon fiber composites. How do...

See similar textbooks

Similar questions

The density of the classified vibranium steel alloy of captain america is suprosinglylow 1.56g/cm^3. knowing the shape of the shield can be properly approximated to a cylinder of radius of 42,9 cm and height of 5.54nm. how heavy is the shape in kg
Determine if each statement is true or false: (a) Substitutionalalloys are solid solutions, but interstitial alloys areheterogenous alloys. (b) Substitutional alloys have “solute”atoms that replace “solvent” atoms in a lattice, but interstitialalloys have “solute” atoms that are in between the “solvent”atoms in a lattice. (c) The atomic radii of the atomsin a substitutional alloy are similar to each other, but in aninterstitial alloy, the interstitial atoms are a lot smaller thanthe host lattice atoms.
4. An alloy has an elastic modulus of 115 GPa. For the alloy, plastic deformation begins at a stress of 275 MPa. (a) If a sample of cross-sectional area 325 mm? is obtained from the alloy, determine the maximum load that may be applied on the sample without plastic deformation. (b) The original sample length is specified as 115 mm, what is the maximum length to which the sample can be stretched without plastic deformation.
(a) Draw an orthorhombic unit cell, and within that cell a (210) plane. (b) Draw a monoclinic unit cell, and within that cell a (002) plane.
(a) Describe the difference between thermoplastic and thermosetting polymers. (b) How are the stiffness, strength, elongation and toughness of polymers evaluated in a quantitative manner? (c) Compare and contrast the physical properties and mechanical behavior of typical polymers in the following classes of materials: (i) flexible plastics (ii) rigid plastics (iii) fibers (iv) elastomers
Some oxide superconductors adopt a crystal structure similar to that of perovskite (CaTiO3). The unit cell is cubic with a Ti4+ ion in each corner, a Ca2+ ion in the body center, and O2- ions at the midpoint of each edge. (a) Is this unit cell simple, body-centered, or face-centered? (b) If the unit cell edge length is 3.84 Å, what is the density of perovskite (in g/cm3)?
(a) A hypothetical compound MB2 crystallises in the rutile lattice structure. (i) Draw the lattice structure of the unit cell MB2. (ii) Show by calculation that the stoichiometry of the formula is consistent with the structure. (iii) Determine the coordination number of the MB₂ unit cell.
(g) Differentiate between hypereutectoid and hypoeutectoid alloys
The thermal and mechanical processing of materials is an important step in ensuring that they have the appropriate physical properties for their intended application. Suppose a metallic element undergoes a phase transit ion in which its crystal structure changes from cubic close-packed to bodycentredcubic. (a) Does it become more or less dense? (b) By what factor does its density change?
At room temperature, the edge length of the cubic unit cell in elemental silicon is 5.431 Å, and the density of silicon at the same temperature is 2.328 g cm-3 . Each cubic unit cell contains eight silicon atoms. Using only these facts, perform the following operations.(a) Calculate the volume (in cubic centimeters) of one unit cell.(b) Calculate the mass (in grams) of silicon present in a unit cell.(c) Calculate the mass (in grams) of an atom of silicon.(d) The mass of an atom of silicon is 28.0855 u. Estimate Avogadro’s number to four significant figures.
estion Four Explain why the average density of metals is higher than that of ceramics or polymers i.e pmetals > (a) Peramics > Ppolymers. (b) Copper crystallises as FCC (face centred cubic). Given that the atomic radius and mass of a given copper sample are 1.28 x 10:10 m and 64.15 g respectively, calculate the density of the copper sample. Take Avogadro's number, NA = 6.023 x 1023 atoms/mole. (c) The linear density, LD, of an atom is given by the equation = Natoms where Natoms is the Ldv number of atoms and Lav is the unit length of the direction vector, both taken on a particular plane. Calculate the linear density of an aluminium atom with a lattice parameter of 4.05 x 1010 m and in a [110] direction. (d) Using neat sketches, show the difference between a triclinic and hexagonal crystal systems.
The maximum wavelength of light that a certain silicon photocell can detect is 1.11 μm. (a) What is the energy gap (in electron volts) between the valence and conduction bands for this photocell? (b) Explain why pure silicon is opaque.