7.5 PQ Estimate the power required to spray water out of thespray bottle that is pictured in Fig. 7.1. Hint: Make appropriateassumptions about the number of sprays per unit time and theforce exerted by the finger. Return-spring-ClosedcheckvalvePistonFigure 7.1In a spray bottle, a pistonpump does work on thefluid thereby increasingthe energy in the liquid.SprayForceBy

Answered: Image /qna-images/answer/4f53caf1-24b7-4245-8bc6-fef7794ea768.jpg

7.5 PQ◄ Estimate the power required to spray water out of the spray bottle that is pictured in Fig. 7.1. Hint: Make appropriate assumptions about the number of sprays per unit time and the force exerted by the finger.

7.5 PQ◄ Estimate the power required to spray water out of the spray bottle that is pictured in Fig. 7.1. Hint: Make appropriate assumptions about the number of sprays per unit time and the force exerted by the finger.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5.1.6- A vapor exits from a nozzle to the atmospheric pressure with a velocity of 490 m/s and a temperature of 150 °C. The nozzle efficiency and the entrance velocity are 0.93 and 150 m/s respectively. Calculate the pressure and the temperature of the steam at the entrance of the nozzle.
A pipe bends through 900 from its initial direction as shown in fig.13. The pipe reduces in diameter such that the velocity at point (2) is 1.5 times the velocity at point (1). The pipe is 200 mm diameter at point (1) and the static pressure is 100 kPa. The volume flow rate is 0.2 m3/s. Assume there is no friction. Calculate the following. a) The static pressure at (2). b) The velocity at (2). c) The horizontal and vertical forces on the bend FH and Fy. d) The total resultant force on the bend. (1)
A Pelton wheel is supplied with 6kg/s of water at 70m/s. The buckets rotate on a mean diameter of 350mm at 1200 rev/min. the deflection angle is 165º and friction negligible. a). Determine the diagram power.(5mks) b). Draw the vector diagram to scale and determine change in water velocity.(5mks)
7
A water plunger pump with a diameter of 150 mm. and a stroke of 250 mm rotates at 50 rpm. The suction pressure is -0.5 kg/cm2 and the delivery pressure is 2 kg/cm2. Neglecting the diameter of the stem and assuming a suction performance of 60% and a delivery performance of 75%. Calculate: a) Force required to move the piston in suction and discharge. b) Useful power of the pump.
Question 13, fluids A centrifugal pump, as highlighted, has an open rotor with a radius of less dimension than the radius of the housing. This causes the rotor input and output slag to occur predominantly in the radial direction. input output 1. 2. 3. h output blades blades input output output Over the years, however, without maintenance, the pump starts to have the entrance into the rotor obstructed at an angle a = 30°, which grows every year, which hinders its inlet flow, without, however, harming the radial behavior of the entrance flow in the region of the blades (in dark gray). If the rotation of 1500 rpm, determine: W the behavior of the velocities before and after the obstruction. The variation of the acting forces. The relative variation of the power of this pump for this rotation.
5. A pump discharges into a spherical tank with a radius of 2 meters. The flow rate is 300 liters/min and fluid specific gravity = 1.1 times that of water (density of H₂O = 1,000 kg/cu. m). Determine flow.rate in kg/sec and time it takes to fill the tank in hours.
3.14 The following data refer to an axial flow blower with a single stage: Mass flow rate=0.75 kg/s Rotor tip and hub diameters=24 cm and 16 cm Rotational speed=3500 rpm As the air flows through the rotor, it turns through an angle of 22° away from the axial direction. Assuming standard atmospheric conditions and that the axial velocity is a constant, compute the degree of reaction and power input to the blower. Also, find the utilization factor. Inlet absolute velocity is purely axial. Ans: P=-252.8 kW; R=0.875
The system curve for a water supply system is shown in the figure below (i.e., red curve). If a 7-inch pump is operating at 1160 rpm, what will be the discharge of water through the system in GPM? Curve no. 2175 Min. Imp. Dia. 6.25" Size 5 x 4 x 7.0 40 HEAD IN FEET 30 25 W 20 10 5 L/SEC 5 7.00" (178mm) 6.75" (171mm) 6.50" (165mm) 15 6.25" (159mm) 7.25" (184mm) O 150 GPM Laco O 350 GPM O 450 GPM O 250 GPM 10 Model 4075 FI & CI Series 15 70% 20 "Dede de 088 A. 25 REQUIRED NPSH 90 1160 RPM November 1, 2010 TM 90- N 00 30 8800 877 1HP(.75KW) de (5 60% ox 35 -10% 5% Tolo 10. 3HP(2.2KW) 2HP(1 5KW). 15HP(1 1KW). CURVES BASED ON CLEAR WATER WITH SPECIFIC GRAVITY OF 1.0 ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ 75 150 225 300 375 450 525 600 675 FLOW IN GALLONS PER MINUTE 45 LOWONG FEET 15 12 9 6 0 6 5 + 2 1 750 NPSH HEAD IN METERS 45 36 OG KPO 27 18 -9 -70 -60 -50 -40 20 10 -0 HEAD IN KILOPASCALS
Example 6.5. An open circuit wind tunnel draws in air from the atmosphere through a well contoured nozzle. In the test section, where the flow is straight and nearly uniform, a static pressure tap is drilled into the tunnel wall. A manometer connected to the tap shows that the static pressure within the tunnel is 45 mm of water below atmosphere. Assume that air is incompressible and at pressure is 100 kPa (absolute). Calculate the velocity in the wind tunnel section (Refer to Fig. 6.6). Density of Po-100 kPa water is 999 kg/m and characteristic gas constant for V=0 Test section 25°C 4-25°C air is 287 /ko K (GATE)
Plz do as fast as possible ....!
Show your correct and complete solution in handwritten. Thank yoouuuu!!