7.5 An ac source is feeding a load that consists of a resistance and reactance connected in series. The voltage and current of the source are as follows: v = 400sin(377t + 0.5236) V i = 100sin(377t + 0.87266) A Calculate the following: a. The resistance and inductive reactance of the load impedance b. The rms voltage across the resistance c. The frequency of the supply voltage d. Power factor at the source side, state leading or lagging e. The real power delivered to the load f. The reactive power delivered to the load

7.5 An ac source is feeding a load that consists of a resistance and reactance connected in series. The voltage and current of the source are as follows: v = 400sin(377t + 0.5236) V i = 100sin(377t + 0.87266) A Calculate the following: a. The resistance and inductive reactance of the load impedance b. The rms voltage across the resistance c. The frequency of the supply voltage d. Power factor at the source side, state leading or lagging e. The real power delivered to the load f. The reactive power delivered to the load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
The single phase AC sinusoidal voltage then the rms value of the voltage v is .........
What is the average power in ghe single phase ac circuit with the purely resistive load? It is sinusoidal steady state excitation.
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
A load is rated at 440V(rms), 7.5A(rms) and 3.3KW when connected to a 50HZ source. Find the load impedance.
The below figure shows the waveform of the voltage and current in a purely inductive AC circuit. Voltage Current Using the voltage phasor as the reference, the current phasor Lags by 90° Is in phase with the voltage Leads by 90° Lags and then leads by 160°
4) Determine the value of voltage across resistor and capacitor5) Convert in rms values
C. Draw a general sine wave V vs t and I vs t plot for a purely resistive and a purely inductive circuit and show leading lagging parameters and clearly mark the phase difference.
a- Find the RMS values of the load voltage and the load currentb- Calculate and draw the voltage across the load inductance