The initial compressive force of a steel column can be determined by Euler's buckling formula. The column has the following properties: A = 9484 mm² Fy = 345 MPa x = 164 x 100 mm² ly = 23 x 100 mm Proportional limit, fs = 290 MPa. The x-axis has an unbraced length of 10 m which is pinned at the top and fixed at the bottom with an k = 0.70. The y-axis has unbraced length of 5 m due to the bracing at the mid-height. Determine the critical buckling load for the boom. E = 200 GPa Select the correct response: 189.50 KN

The initial compressive force of a steel column can be determined by Euler's buckling formula. The column has the following properties: A = 9484 mm² Fy = 345 MPa x = 164 x 100 mm² ly = 23 x 100 mm Proportional limit, fs = 290 MPa. The x-axis has an unbraced length of 10 m which is pinned at the top and fixed at the bottom with an k = 0.70. The y-axis has unbraced length of 5 m due to the bracing at the mid-height. Determine the critical buckling load for the boom. E = 200 GPa Select the correct response: 189.50 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The initial compressive force of a steel column can be determined by Euler's buckling formula. The column has the following properties: A = 9484 mm² Fy=345 MPa 1x = 164 x 100 mm4 ly = 23 x 105 mm² Proportional limit, f = 290 MPa The x-axis has an unbraced length of 10 m which is pinned at the top and fixed at the bottom with an k = 0.70. The y-axis has unbraced length of 5 m due to the bracing at the mid-height. Which of the following most nearly gives the axial force in the boom? Select the correct response: 104.62 kN 43.33 kN 94.75 kN 38.14 kN E = 200 GPa
The initial compressive force of a steel column can be determined by Euler's buckling formula. The column has the following properties: A = 9484 mm² Fy=345 MPa x = 164 x 106 mm4 ly = 23 x 106 mm4 Proportional limit, fs = 290 MPa The x-axis has an unbraced length of 10 m which is pinned at the top and fixed at the bottom with an k = 0.70. The y-axis has unbraced length of 5 m due to the bracing at the mid-height. Compute the initial compressive load of the column. Select the correct response: 6606.59 KN 3706.14 KN E = 200 GPa 1816.01 kN 926.53 kN
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.75 in.2 and bar (2) has a cross-sectional area of 0.45 in.2. After load P is applied, the strain in bar (1) is found to be 850 μεμε. Assume L1=53 in., L2=79 in., a=34 in., b=33 in., and c=30 in. Determine:(a) the stresses in bars (1) and (2).(b) the vertical deflection vD of point D on the rigid bar.(c) the load P.
2) The rigid bar ABC is horizontal before the load Pis applied as shown in the figure. Determine the maximum safe value of P if the stress in the steel bar is limited to 300 MPa and the stress in copper bar is limited to 140 MPa. Use E = 200 GPa for steel and E 120 GPa for copper. Neglect the weight of the bar ABC. D copper bar. A=520mm? steel bar. A=320mm B 2.00m 1.00m 1.00m 1.00m 1.50m
The support in Figure 14.21a is to be constructed from a 4340 steel plate tempered at 800◦F. The yield strength of the steel is 228 ksi, and; its value of KIc is 51 ksi√ (in.). The width of the support, w, is 4 in.; the length, L, is 36 in.; and the thickness, t, is 0.25 in. Figure 14.21b gives f(a/w) in the equation σ = KIc/[f(a/w) √ (πa)]. A. If the crack length, a, is small enough, the support will yield before it fractures? What is the size of the largest crack for which this is true (i.e., what is the largest value of a for which general yielding will precede fracture)? Assume that any fracture would be in mode I (plane strain). Discuss critically the assumption of mode I. B. If it is guaranteed that there are no cracks longer than a length equal to 80% of that in Figure 14.21a, does this assure that failure will occur by yielding, rather than fracture? Explain briefly.
Rigid bar ABCD is loaded and supported as shown. Steel [E = 29900 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.73 in.² and bar (2) has a cross-sectional area of 0.47 in.². After load P is applied, the strain in bar (1) is found to be 800 με. Assume L₁-52 in., L₂=90 in., a-36 in., b-34 in., and c-23 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vp of point D on the rigid bar. (c) the load P. (2) (1) L₁ B C a Answers: (a) σ₁ = (b) VD = (c) P = i i L2 b C ksi, 0₂ = i in. kips. D P ksi.
Rigid bar ABCD is loaded and supported as shown. Steel [E = 29900 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.81 in.2 and bar (2) has a cross-sectional area of 0.46 in.2. After load P is applied, the strain in bar (1) is found to be 770 με. Assume L1=55 in., L2=78 in., a=31 in., b=31 in., and c=36 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vD of point D on the rigid bar. (c) the load P.
2)For the supporting frame shown below: a) Determine the internal forces acting at section a-a. b) Determine the stress components that act at points A and B. IN = 2.6525x10-7 mª -300 mm 150 mm 2.5 kN a 12 mm 6 mm 6 mm 6 mm 36 mm'36 mm Section a – a
Three bars AB, AC, and AD are pinned together as shown in the figure. Initially, the assembly is stress free. Horizontal movement of the joint at A is prevented by a short horizontal strut AE. Calculate the stress in aluminum bar AC and steel bar AD. Also, find the force in the strut AE when the assembly is used to support the load W = 12.50 kips. For each steel bar, A = 0.4 in² and E = 29 × 106 psi. For the aluminum bar, A = 0.8 in² and E = 10 × 106 psi. B с D 20% Steel E Aluminum 35 W A Steel L
Three bars AB, AC, and AD are pinned together as shown in the figure. Initially, the assembly is stress free. Horizontal movement of the joint at A is prevented by a short horizontal strut AE. Calculate the stress in aluminum bar AC and steel bar AD. Also, find the force in the strut AE when the assembly is used to support the load W = 12.50 kips. For each steel bar, A = 0.4 in2 and E = 29 × 106 psi. For the aluminum bar, A = 0.8 in2 and E = 10 × 106 psi.
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E, = 200 GPa , and E, 150 GPa E, = = 200 GPa 4 kN/m 20 mm 60 mm BA E E2 = 150 GPa 20 mm 50 mm 5 m 3 m |-1.5 m--1.5 m-- 3 m
The section of a thick beam has the dimensions shown in the figure below. Calculate the section properties lz, ly and Izy (Izy = product of inertia) referred to horizontal and vertical axes through the centroid of the section. Refer to Section 6 in your notes for properties of planed sections. Also determine the direct stress at the point A due to a bending moment M, = 55 Nm. Ay A 5 mm 20 mm G 5 mm 5 mm 10 mm