6.64 Consider application of the naphthalene sublimation technique (Problem 6.63) to a gas turbine blade that is coated with naphthalene and has a surface area of A, = 0.05 m². Airflow V.T_ وما - Turbine blade with naphthalene coating A., T., P. (T) To determine the average convection heat transfer coef- ficient for a representative operating condition, an experiment is performed in which the coated blade is exposed for 30 min to atmospheric air at the desired velocity and a temperature of T = 27°C. During the experiment the surface temperature is T. = 27°C, and at its conclusion the mass of the blade is reduced by Am = 8g. What is the average convection heat transfer coefficient associated with the operating condition?

6.64 Consider application of the naphthalene sublimation technique (Problem 6.63) to a gas turbine blade that is coated with naphthalene and has a surface area of A, = 0.05 m². Airflow V.T_ وما - Turbine blade with naphthalene coating A., T., P. (T) To determine the average convection heat transfer coef- ficient for a representative operating condition, an experiment is performed in which the coated blade is exposed for 30 min to atmospheric air at the desired velocity and a temperature of T = 27°C. During the experiment the surface temperature is T. = 27°C, and at its conclusion the mass of the blade is reduced by Am = 8g. What is the average convection heat transfer coefficient associated with the operating condition?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.16P

See similar textbooks

Similar questions

Hot fluid "C 2562 J/kg.k, Pr 51.3, u-5.22E-3 Pa.s, k0.260 Wm.K" flows af 0.8 kg/min inside a 3-mm diameter, thin walled tube. The tube is coiled and submerged in a water bath maintained at 23 C. The fluid experiences a temperature drop of 63°C and leaves the tube at 35 C. What is the required lengih of the tube "m Neglect heat transfer enhancement associated with the coiling. Assume ftlly developed flow, If turbulent flow use Dittus Boelter equation: Nn 0.023 Re Pr
6.64 Consider application of the naphthalene sublimation technique (Problem 6.63) to a gas turbine blade that is coated with naphthalene and has a surface area of A, = 0.05 m². Airflow V,T_ - Turbine blade with naphthalene coating A., T., P. (T₂) To determine the average convection heat transfer coef- ficient for a representative operating condition, an experiment is performed in which the coated blade is exposed for 30 min to atmospheric air at the desired velocity and a temperature of T = 27°C. During the experiment the surface temperature is T. = 27°C, and at its conclusion the mass of the blade is reduced by Am = 8 g. What is the average convection heat transfer coefficient associated with the operating condition?
Design a hydrocooling unit to cool down fruits and vegetables from 30 °C to 5 °C in 20 minutes at a rate of 20,000 kg of fruit or vegetables/h. The design must fulfill the following requirements: The unit will be an immersion flooded system. It must be able to cool down and transport the products in chill water. The tank has the following dimensions approximate. three meters wide and up to 90 cm hight. The water will circulate and be cooled through the evaporation section of a refrigeration system. The refrigerant temperature inside the coils will be -2 °C, and the water temperature must not drop below 1 °C and must not exceed 6 °C. Assuming reasonable values for the average density, specific heat, and porosity of the product (the fraction of the volume of air in a box), recommend reasonable values for: The speed of the water through the canal, the capacity of the cooling system. the compressor power.
* Hot air enters a sheet metal đuct located in a basement. Determine the exit temperature and the rate of heat loss. Taking k 0.02735 W/m. C, v= 1.797x10 m'/s. Pr 0.7228, C-1007 J/kg.C ,pD MSc. Rasha Nasser 106 1.092 kg/m' H= 2.325 kg/m.s and e = 0.3 Ans: 45.1 °C, 2622 W Air dust 20 cm - 20 em Air L-12 m
A Copper ball at 40'Cis dropped in a mug containing water at 40°C. The heat will Select one: O a.not flow from Copper ball to water or from water to Copper ball O b. flow from Copper ball to water O c. Increase the temiperature of both O d. flow from water to Copper ball
A small-scale Compressed Air Energy Storage (CAES) system uses a rigid tank, whichhas been sized to 1m3. The air storage helps support various fluid power (pneumatics)requirements, but also serves for energy storage (when fully charged).The tank sits in a plant room having a temperature of 25oC at 1 atmosphere (101.325kPa).When delivered new and installed the tank (and the ambient air it contains) is assumedinitially at the same steady state conditions in the plant room. The tank can be filled with(dry) air to a maximum pressure of 300bar. When left in the plant room, the pressurised airtank eventually attains the plant room temperature.You may assume:> Steady state conditions apply> Negligible changes in kinetic and potential energy> Thermal mass of the tank (metal) is negligible Apply the ideal gas equation and calculate the mass of 25oC air (units: kg) in the fullypressurised tank.
B/A boiling channel receives a thermal power of 6000 kw. If subcooled water at 275 °C enters the channel at a flow rate of 15 kg/s what is the void fraction at the channel outlet where the slip ratio is 1.687 and pressure is 68 bar. Given data: At 68 bar: h=1256 KJ/Kg, hg-1518 KJ/Kg, V-1.344*10-³ m³/Kg, V-28.27*10³ m³/Kg
Example: A 1.0 kw heater is Constructed ofaglass plte with an electrically condcting film which produčes' a Constant hent flux . The plate is 60x 60 cm and placed in an air sebeetote stream at 27c ,d atm with Uo=5 m/s. Calculate the average temp. difference along the plate, and the difference at the trailing edge.
When viscous dissipation is appreciable, the energy balance of a convective system must include the viscous effects of the fluid, so a third term is added to the energy balance: A slide bearing (pillow block) can be idealized as a static plate and a plane that moves parallel to it. The rotary axis of such a system has a diameter of 100 mm and rotates at 3600 rpm inside the bearing, which has a gap between the plates of 0.5 mm. The system is lubricated by oil, with a density of 800 kg / m, a viscosity of 0 01 kg / ms and a thermal conductivity of 0:14 W / mk. The top and bottom surfaces of the bearing are at 60 ° C. Considering the viscous effects of the oil, determine a) The maximum temperature of the oil. FC b) Bottom plate heat flux per unit length W / m Write down all assumptions made
A thin liquid film of ammonia (NH3), which has formed on the inner surface of a tube of diame D= 10 mm and length L = 1 m, is removed by passing dry air through the tube at a flow rate m = 3 x 104 kg/s. The tube and the air are at 25°C. a) Calculate the velocity, the Reynolds number Rep and Sherwood's number Sc. b) What is the average mass transfer coefficient hm? (Hint: Use Table 14-13)
Prlen # 9. Solve for: a) heat tranefer pate of ayatem ) mass Mow rate bath Atreams. Ueing a double kipe Reat eschunger (imside di anaeten =0.38 m, %3D outside diaetu = 0.40 m total length= 0.14 m steam (0.12 mPa kas wndengme The steam conde na atiin method. wtili ged peservoir water flow, outlet ald fluid temp. = at 306.95 K using 321.85 K countereurrent Uaing ouerall neat tranefer outride Aurface area, Crefficint: Uo-5219.97 W/m² K
Estimate the mass-transfer coefficient for moist air flowing normal to a 25 mm diameter tube (Nu = 0.615 Re0.47). The air velocity is 0.5 m/s. Assume standard air.