6. The frame ACD is supported by ball-and-socket joints at A and D and by a cable that passes through a ring at B and is attached to hooks at G and H. Knowing that the frame supports at point C a load of magnitude P= 268 N, determine the tension in the cable. 0.925 m G 1 0.35 m 0.5 m 0.5 m 0.875 m H D 0.75 m 0.75 m

6. The frame ACD is supported by ball-and-socket joints at A and D and by a cable that passes through a ring at B and is attached to hooks at G and H. Knowing that the frame supports at point C a load of magnitude P= 268 N, determine the tension in the cable. 0.925 m G 1 0.35 m 0.5 m 0.5 m 0.875 m H D 0.75 m 0.75 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

....An electric motor drives a compressor by use of V-belt. The angle of contact on the smaller pulley is 2.89 rad and the belt speed runs at 29.36 m/s. The groove angle of the pulleys is 35°. Determine the tension in the slack side of the belt in N if the belt has a cross-sectional area of 366 mm2, density 1000 kg/m3, and an allowable tensile stress of 2.3 MPa. The coefficient of friction between the belt and the pulley is 0.3
5.2) For the frame and loading shown, identify the two and three force members and determine the reactions at C and D. 150 N Road map 2/3 Force member Problem FB0D • ISON B 26.57⁰ Im Efy = -150+ F Sin (26.5x) - Cy= M √2 1 0.5m Р 63.430 L B 1 A C Bar BD is a two force member, Bar ABC is a three Force Governing equations 2Fx 180 Cos(26.57) + (x =O Im member 0.5m 0.5m
Calculate the forces in members AB, BH, and BG. Members BF and CG are cables which can support tension only. Forces are positive if in tension, negative if in compression. A 5m B 5 m 54 54 Answers: AB = i BG= BH = i 8 KN H i G 16 kN c 5 m 54° 54% E D kN kN kN
Four sets of flexible cables, spaced at 120° intervals, are used to stabilize a 400-ft communications tower. The tower and one cable from each set is shown in Fig. The weight of each tower is 40 lb/ft, and the communica- tions equipment at the top weighs 2000 lb. Determine the axial forces transmitted by transverse cross sections at points A, B, C, and D of the tower. 50 ft 30 1500 lb 100 ft B 40° 1250 lb 100 ft 50° 1000 lb 100 ft 50 ft 60 750 Ib
Two double-threaded square power screws have root diameters of 2 in. each and pitches of 0.5 in. each. Both are arranged in parallel and areused to convey a load of W = 502 lbs using a motor that rotates at 300 rpm. Determine the force F for each screw (in N) applied at the end of a lever 3 ft long if these power screws lift the given load.
Q.3) The coefficient of friction between the 100 lb block (shown in figure below) and the incline plane is 0.25 and that between the cord and cylindrical support is 0.3. Determine the range of cylinder weight W for which the system shown below will be in equilibrium. p = 0.3 100 lb p = 0.25 25° W
Problem 1 Detemine the reaction at A and C. Support at A is fixed, C is roller support, and B is pin- connected. 7.6 kN 10 KN/m 1.5m B. 2m 4m Problem 2 Detemine the reaction at A and B. Support at A and B are pinned and C is pin-connected. 12.65 kN 15 kN 2m 2m 3m B 4.5m 3.5m 10.3 kN/m
A stadium roof truss is loaded as shown, with P = 3kN. Determine the force in members DF. 3 m 3 m 4 m--4 m--4 2 kN 1.5 kN 2 kN F 1 kN 0.75 kN G D 6 m A H C E 6 m 6 m 6 m
The structure consists of a spring CD and a solid member ABC with a slot at B. The peg at B fits loosely into the slot at B and can hence be interpreted as a smooth support. The unstretched length of the spring is 80 mm. 50 mm 150 mm 50 mm A D C B k = 600 N/m 1.1 Draw separate free-body diagrams of member ABC and the spring CD. 1.2 Comment on the existence of two-force members and three-force members in this system. 1.3 Determine the reactions at A and B on the member ABC
A 500-lb block W is supported by a boom CB and The boom a flexible cable AB as shown in Fig. weighs 250 lb, and the cable weighs 2.5 Ib/ft. Determine the maximum tension in the cable, the length L of the ca- ble, and the sag h at midspan. Assume that the weight of the cable is uniformly length. distributed along its horizontal 20 ft 16 ft W
Calculate the forces in members AB, BH, and BG. Members BF and CG are cables which can support tension only. Forces are positive if in tension, negative if in compression. 6 KN 9 kN 4 m в 4m C 4 m D. 56 56 56 56 H E Answers: AB = i kN BH = i kN BG = kN
The cable shown in Fig. distributed load of 25 kN per meter of horizontal length. The left support of the cable is located 50 m below the right support. The angle between the cable and the horizontal at the left support is 10°. Determine carries a uniformly The tension in the cable at the right support. 50 m 10 150 m-