6. Investigate the tension member connection as shown in Figure below to carry a total service load of 75 kips. The connection is a bearing type connection with threads exclude (from shear planes, using 7/8 in diam. A325 bolts in standard holes). The plates are A572 Grade 50 steel. Use the AISC Specification. O O O Plates 5 Assume standard size holes X6 <- T

6. Investigate the tension member connection as shown in Figure below to carry a total service load of 75 kips. The connection is a bearing type connection with threads exclude (from shear planes, using 7/8 in diam. A325 bolts in standard holes). The plates are A572 Grade 50 steel. Use the AISC Specification. O O O Plates 5 Assume standard size holes X6 <- T

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter7: Simple Connections

Section: Chapter Questions

Problem 7.6.3P

See similar textbooks

Similar questions

Determine the maximum Pu that the connection can resist. Use 25 mm Ø A490-X bolts and 12 mm, A-50 plates. Assume that edge distance and bolt spacing are not critical. Use LRFD. 246 mm 76 mm 12 mm 25 mm 73 mm 74 mm 27 mm 56 mm
Determine the maximum service load P (ASD) that the connection can resist. Use 27 mm Ø A490-N bolts, and 10 mm A-36 plate and a load P with a slope 1H: 2V. Assume that edge distance and bolt spacing are not critical. ***Note: Lod P is acting at a slope of 1H: 2V
The bolted connection shown is a bearing type connection. Which of the following best gives the shearing capacity, ØRn. of the bolts? Consider threads excluded from shear plane and deformation at bolt hole is a design consideration. Standard size holes. PL350x12mm = 250 MPa C250x22.8 70 114 M20 A490 70 40' 60' 60 '40 SECT. A d tw bf tf Mm 15.8 mm^2 mm mm mm mm C250x22.8 2880 254 6.1 65 11.1 Ix(10^6) Sx(10^3) ly(10^6) Sy(10^3) Zx(10^3) Zy(10^3) rx ry mm^4 mm^3 mm mm^4 mm^3 mm mm^3 mm^3 27.7 218 98.1 0.912 18.5 18.5 257 40.3 O 424.8 KN O 1,102.7 KN O 3,770.7 KN O 1,637.1 KN
Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm diameter bolts. 12 mm bolts t=12 mm t=12 mm P. P- P 300 75 75 75 Edge distances -75 mm dhole for tensile and rupture d, +3 mm dnole for bearing strength for L- de +1.5 mm Fy 248 MPa F.- 400 MPa
Determine the design strength ?nPn and the allowable strength Pn/Ω of the connection shown if 3/4-in A502, Grade 1 rivets and A36 steel are used. Assume Fv = 25 ksi and threads excluded from shear planes.
5) Calculate P the allowable tensile load for the butt joint shown. Each A325-N high-strength bolt has a diameter of 0.9 inches. The plates are made of ASTM A36 steel. If the applied load is 200 kips, is this connection adequate? If not, what needs to be changed so that this connection can handle an applied load of 200 kips? P- ФФ P ! 12"x " P. P.
Compute the capacity of the connection considering all possible modes of failure. Assume that the determination @ bolt is a design consideration, A490 bolt are used with threads included from shear planes.
(2) Determine the LRFD design tensile strength and the ASD allowable tensile strength for the bearing-type connection as shown below. The steel is Fy = 36 ksi and Fu = 58 ksi, the bolts are ¾ -inch diameter A325, the holes are standard sizes and threads are not excluded from shear plane. Assume deformation at bolt holes are a design consideration, ignore the block shear mode and bolts are snug-tight. P/2- PL 1 x 12 P/2E PL 1 x 12 2 in 3 in O O O 3 in 2 in 13 in [3 in 13 in 13 in PL 1 X 12 P
Check the bolted section of the given gusset plate connection assuming that the connection is done by M12 bolts with a staggered arrangement. The maximum design tensile axial force to be sustained is Ned = 168 kN. Assume a grade of S235 steel. P. Gusset plate BỘ do=13mm Gusset plate O DO t=16mm t-16mm1 Ni.Ed FO NtEd do=13mm do3D13mm G. 40mm 40mm 140 mm 240mm 30mm
Answer asap for an upvote. Thank you. in the connection shown in the figure,the bolts are 3/4 inch in diameter and A50 steel is used for all components. compute for the nominal block shear strength (kips) of front plate
Problem 1: A butt joint shown in Figure ST – 127 using A325 bolts with a diameter of 16 mm with threads excluded in a shear plane. The plate used is A36 steel with Fy = 400 MPa. Use LRFD. Hole diameter is 3 mm larger than the bolt diameter. 1. Compute the design strength Pu of the connection based on bearing of the plate. Hint: The inner plate will govern. No need of checking the outer plate. 2. Compute the design strength Pu of the connection based on bolt shear. Hint: the bolt is in double shear. As is times 2 for every bolt. |32 84 84 12.5 mm T/2 T/2 22 mm 12.5 mm T/2- T/2 + T 180 mm Figure ST - 127
6) The connection shown in the figure uses 20mm diameter A325 bolts. The tension member is A36 steel (Fy = 248 MPa, Fu = 400 MPa) and the gusset plate is A572 steel (Fy=290 MPa, Fu = 415 MPa). Determine the design strength of the connection (in kN) considering block shear rupture. 37.5 mm 75 mm 37.5 mm 9 mm gusset P 12 mm x 150 mm 37.5 mm 75 mm 37.5 mm