6. For the beam and loading shown, calculate (a) the equation of the elastic curve for portion BC of the beam, (b) the deflection at midspan, (c) the slope at B. The beam is W200X46.1 with E-200GPa and load density of 5000N/m with L-6m P=WL A 101010 22-1 W IC X

6. For the beam and loading shown, calculate (a) the equation of the elastic curve for portion BC of the beam, (b) the deflection at midspan, (c) the slope at B. The beam is W200X46.1 with E-200GPa and load density of 5000N/m with L-6m P=WL A 101010 22-1 W IC X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: An 5355 Class 1 laterally restrained universal beam (UB) does not support a high shear load. What is…

A: Given data, S355 Class1 laterally restrained universal beam Flange thickness=f=34.3 mm Wez=235x1000…

Q: The section shown below is made of 50 ksi A992 steel. The x-axis is lateral and the y-axis is…

A: Given: The yield stress of the steel is 50 ksi. Consider the figure,

Q: From the given figure below, determine the minimum height of the beam if the flexural stress is not…

Q: The ratio of the maximum deflections of a sim ply supported beam with a central load w and of a…

Q: Calculate maximum deflection in a simply supported beam under UDL Support Reactions Internal Bending…

Q: For the inverse T-section beam that loaded as shown in figure, find the maximum tensile and…

A: A double overhanging beam is given we need to find out maximum tensile and compressive bending…

Q: For the beam with the cross-section shown and loads as follows: w-2 kN/m, M-4 kN-mand PkN, P-5.XY…

Q: The section shown below is made of 50 ksi A992 steel. The x-axis is lateral and the y-axis is…

A: Given: The yield stress of the steel is 50 ksi. Consider the figure,

Q: The cantilever beam shown in figure (2) supports the roof of a workshop shed "no-ceiling". Design…

A: l = 18feet = 216inch w = 1.3 + 2.7 = 4kip/ft M = wl2/2 = 4 x 182/2 = 648 kip-ft Let the material be…

Q: by 늘 wo B 늘 C X

A: Given Data:Length L=6.3md=300mmbf=215mmtf=14mmtw=10mmIt is required calculate the largest intensity…

Q: 6. For the beam and loading shown, calculate (a) the equation of the elastic curve for portion BC of…

Q: 3.4 Check the threshold validity below according to the bending requirement if 35MPa=m, f = 300 MPa.…

A: Dead load, DL = 5 kN/mLive Load, LL = 10 kN/mPL = 20 kNSpan, L = 4 mfc = 35 MPafy = 300 MPa3-25 mm…

Q: ed at the two vertical supports only. a) What is the allowable bending stress in the beam in MPa? b)…

A: Given:- W18X 97 steel beam A-36 steel (Fy = 250 MPa). A. If the beam is laterally su A=18387 mm2…

Q: For the beam shown below: a) Calculate the elastic curve equation Ely Mo A = R³L 6 Mox³L + cx + C₂…

Q: below, calculate the principal values of stress. S stresses acting on a properly oriented material e…

Q: A composite shaft arrangement of brass and steel is shown below. The allowable shear stress are 100…

A: A composite shaft made of brass and steel.The diameter of the steel part is 80 mm.The diameter of…

Q: art 1 The simply supported beam below is initially designed to undertake a concentrated factored…

A: According to given data

Q: A flat steel bar, 26 mm wide by 4 mm thick and 1.8 m long, is bent by couples applied at the ends so…

Q: A simply supported beam with span of 8m is subjected to a counter clockwise moment at the left…

Q: A flat steel bar, 27 mm wide by 2 mm thick and 1.2 m long, is bent by couples applied at the ends so…

A: Given: Flat steel bar dimensions Mid point deflection Modulus of elasticity To find: Maximum…

Q: For the cantilever beam loaded as shown in figure. The deflection at the free end is zero. The ratio…

Q: A flat steel bar, 25 mm wide by 3 mm thick and 1.7 m long, is bent by couples applied at the ends so…

A: Here, we have used two formulae 1. Max deflection at mid point due to couple at end…

Q: Compute the maximum deflection for the beam loaded as shown below 400 Ib 400 Ib 160 Ib/ft 100 Ib/ft…

A: To find Maximum deflection for the beam

Q: Q4: If the T- cross section of the beam shown in the Figure (3) below has bending stress of 37 MN/m²…

Q: 3. The beam and loading shown in figure below, is a simply supported beam with a span of 7.2 m and…

A: Given that :-a simply supported beam has following specifications :- a) span = 7.2 mb) the service…

Q: Per missible As in section to ensure tensile Compute the design strength of beam shown if fy = 420…

A: To find : design strength

Q: A simply supported beam is 4m long and has a load 200 kN concentrated at middle. The flexural…

A: A simply supported beam, Length = 4mConcentrated load at middle point = P= 200kNEI= 300MN-m² =…

Q: 1.) The total area of the section in in² 2.) The gross moment of inertia in inª 3.) The cracking…

A: Compressive strength of concrete, f'c = 4000 psiFlexural strength of concrete, fr = 7.5Reinforced…

Q: 183

A: Blade design consists mainly of selecting the aerofoil section(s) that comprise the blade, and then…

Q: A 210 kN axial compressive load is applied to a W530x101-steel column with the length of 3.20 m and…

A: The total stress acting on the column=Direct stress+ Bending stress The direct stress is given by;…

Q: Need help asap pls. The beam is shown below. The cross-section of the beam is 250 mm x 400 mm. Take…

A: Given Data E = 200 GPA Cross section of beam 250 mm × 400mm Find 1. Deflection at right end of…

Q: Compute the loads and deflections point D at each yield and the ultimate level for the structure…

A: The forces are the amount of loading that happened on the area required by the specimen. The…

Q: B F2 C D F4 F1 A. F6 F3 F5

A: in member AB member force is 20KN in member BD member force is 32 KN in member DE member force is…

Q: Two circular shafts are joined together between fixed supports to resist a torsional moment of 80…

A: Using equilibrium and compatibility establish the equation of equilibrium and solve them to get the…

Q: A steel built-up section is made by 3-W760 x 314 steel sections as shown in the figure. a) if the…

A: (a) h=7852=392.5 mm x=7852+19.72=402.35 mm

Q: Strictly show all of the free body diagrams used upon solving the problem. Complete solution is a…

Q: Q4/ A steel bar is 18cm long and has a diameter of 18mm carries a maximum tensile load of 400 N/mm 2…

Q: Beam and load cases Maximum Beam Deflection PL³ dmax 3EI

A: To find maximum deflection of cantilever beam

Q: Question 4 A 100mm diameter solid aluminium post is subjected to a bending moment of 2KNm, and a…

Q: For the beam shown in Figure-4, using plastic analysis theory determine the value of P. with respect…

A: Given:- A beam is shown with three-point loads acting on it The magnitude of the point load 1 = 2Pn…

Q: KOBLE The lap joint in the figure is made using a 30 mm diameter bolt. The Duter plates are 5 mm…

A: Given Data:-⇒d=30mm (S355 steel)⇒top=5mm (2014-T6 aluminium)⇒tip=10mm (6061-T6 aluminium)⇒FOS=…

Q: .: For the composite structure shown in Figure, using unit load method (virtual work method), find…

A: A beam is hinged at A and supported by a link of 3m at C.The beam is loaded with a UDL of 10kN/m The…

Q: The beam is loaded as shown. Determine the dimension of the square beam if the maximum flexural…

A: Maximum moment : Maximum moment occur at fix end MMax=-16×7-4×6×(3)=-184 KN-m Bending stress…

Q: composed of an aluminum section rigidly attached between steel re sections, as shown in Fig. Axial…

Q: Absolute value of bending torque Max = ? kNm Width of the web (integer) = ? mm

A: Given Data: The yield strength of the aluminum material of the beam is σy=280 MPa The width of the…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

6. For the beam and loading shown, calculate (a) the equation of the elastic curve
for portion BC of the beam, (b) the deflection at midspan, (c) the slope at B. The
beam is W200X46.1 with E-200GPa and load density of 5000N/m with L=6m
P
L
A
-LR
B
W
L
C
X

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Reactions calculation

VIEW

Step 3: Slope and elastic curve equations

VIEW

Step 4: Elastic curve equation of BC

VIEW

Step 5: Deflection at mid span and slope at B

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need the answer as soon as possible
For the beam and loading shown, check if the maximum bending stress is less than the allowable bending stress using the ASD approach. The self-weight of the beam is denoted "waw", and the steel beam is a "W10x26". Assume the beam has an allowable stress due to bending of 21 ksi. See the next page for section properties of the steel beam. Assume the steel cross-section is being bent about its "strong axis" - i.e. the "x-axis". PL = 5.0 kip Wsw B 10 ft
Asap
Consider the figure 1 below: 3-25mmø bolts are used to fasten a plate to a steel beam a) Determine the average shearing stress caused in each bolt by the 30kN loads. b) Determine the value of additional load P that must be applied so that each bolt will not exceed the maximum shearing stress of 6OMPA. 30 kN 150 300 200 P 30 kN 75 Foot
Current Attempt in Progress The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; = 1990 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA= 250 kip-ft, P= 14 kips, LAB = 4.1 ft, LBc = 6.2 ft. MA LAB LBC Answer: in. (a) VA- in. (b) VB - 4. Submi Attempts: 0 of 1 used Save for Later
Please correct answer
For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural stresses at support for point (a) is ..................... MPa * 120mm 16.2kN 16.2KkN —{ 10.2KN/m £ fj//’/ £ W @ Q| im 3m im = 30 mm thickness of walls cross section Your answer
Q1: A simply supported reinforced conerete beam has a cross-seetion as shown in the Figure 1. Using Working Stress Method to calculate maximum load (Wmax.). (Neglect self-weight), use fe=21 MPa and 6=420 MPa Wea 40 25 2m 6m- + 300 mm Figure 1 ك إضافة ملف
It is not graded question and it is complete question.Plz, solve it for your understanding.Structural Analysis-2Plz, write as this process: Given Data Required solution Results Attempt Neat and Clean with proper diagrams
Strength of material
A simply supported pre-tensioned T-beam, as shown in Figure (2) has: f'ci 25MPa; f'-40 MPa; span length is 12m; Total Aps-800mm² for tendons; initially stress in the tendons is 1000 MPa. Consider 20% the total losses of pre stressed force then determine the allowable service live load can be carrying. 150mm 600mm T 500mm T Aps-800 mm² 50mm 150mm Typical Cross section Figure (2)
Plase answer questions from (d)