3. An engine working on the Otto Cycle has a compression ratio of 10/. At the beginning of the compression stroke the temperature of the air is 30°C. After the addition of heat constant volume the temperature of the air rises to 1100 °C. Find the heat supplied, heat rejected & the net work done per kilogram of air in the cylinder. What is the efficiency of the cycle?

3. An engine working on the Otto Cycle has a compression ratio of 10/. At the beginning of the compression stroke the temperature of the air is 30°C. After the addition of heat constant volume the temperature of the air rises to 1100 °C. Find the heat supplied, heat rejected & the net work done per kilogram of air in the cylinder. What is the efficiency of the cycle?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pls show the complete solution with pv, ts diagram and please use english system unit. Thanks!! ?
5
You are required to design a spark ignition engine with a compression ratio of 9. the cycle pressure is 1 bar and the temperature is 300K. The maximum temperature in the Assuming a cold air standard process analyze the appropriate cycle. At the beginning of cycle is 2000K (a) Show the cycle on a p-v and T-s diagram (b) Calculate the heat transfer and work per unit mass of air. (c) Calculate the thermal efficiency (d)Assuming all the heat is transferred at high and low temperature what is the maximum efficiency of the cycle. Justify your answer.
Plz solve in 45min
Q3:A small truck has #cylinder ,4 liter compression ignition engine that operates on ir standard Dual cycle with air fuel ratio of 16:1, the compression ratio is 17 and the cylinder diameter is 14.5Cm. At the start of compression stroke Ta=50'C and Pa=100 kpa .It can be assumed the half of the heat input is added at constant volume and halt at constant pressure Calculate: 1-Temperature and pressure at each state of the cycle. 2-Indicated thermal efficiency. 4:28 PM
Diesel cycle releases 1750 J/mol ofheat. The pressure and temperature at the begin-ning of the compression step are 1 bar and 50°C,and the pressure at the beginning of the expansionis 5 bar. The working fluid is an ideal gas for whichcP= 7R/2 andcV= 5R/2. (a) What is the tem-perature at the end of the adiabatic expansion? (b)What is the heat absorbed by the engine? (c) Whatis the compression ratio? (d) What is the work doneduring the compression step?
Air temperature 30 ° C pressure 1 bar flows into the ideal gas turbine cycle by a pressure ratio air compressor (r). 12 The hot gas discharge temperature from the combustion chamber is 1200 K. The air flow in a constant cycle is 60 kg/s a. Draw the diagram T-5 of this cycle b. Find the net power output (kW). C. Find the thermal efficiency of this cycle
An air-standard Compression Ignition cycle has a compression ratio of 18.2. Air is at 32000R at the end of the heat addition process. Neglecting the variation of specific heats with temperature,determine the following:a. Cut-off ratiob. Net output work of the cyclec. Heat rejection per unit mass, Btu/lbd. Thermal efficiency of the cycle(%). Compare this efficiency value if the cycle has to run on an airstandard Carnot Cycle.
Given in Table are the pressure and temperature of the steam as it enters the turbine as well as the pressure in the condenser. The given engine operates on a simple ideal Rankine cycle, calculate the unknowns in Table. Show solution Rankine Pressure of Temperature Pressure at the Net work Heat Thermal entering the Efficiency (n) in % the steam entering the entering the condenser system (WN) boiler (Qin) turbine (Rx) turbine (t+) in MPa Engine of the steam done by the in KJ/kg in KJ/kg (Pe) in kPa in °C A 3 350 75
I need handwritten only otherwise skip I'll rate
An iseal Brayton cycle has a pressure ratio of 6:1. The temperature of the air is 22 degrees celsius at the inlet to the compressor and 1080 derees celsius at the inlet to the turbine. Take specific heat at constant pressure and constant volume for air as 1,006 KJ/kg K and 0,717 KJ/kg K respectively. Calculate: 1. the compresion absolute temperature to one decimal place 2. the work ratio of the plant to three decimal places 3. the specific work output to the turbine and specific work input to the compressor , to one decimal place and SI unit 4. the thermal efficiency of the plant to one decimal place
The compression ratio of Otto cycle is 8.5. If maximum temperature of the cycle is 11900C, find the temperature after expansion.