5.5-12 A small dam of height h = 2.0 m is constructed of vertical wood beams AB of thickness t = 120 mm, as shown in the figure. Consider the beams to be simply supported at the top and bottom. Determine the maximum bending stress omax in the beams, assuming that the weight density of water is y = 9.81 kN/m³. h

5.5-12 A small dam of height h = 2.0 m is constructed of vertical wood beams AB of thickness t = 120 mm, as shown in the figure. Consider the beams to be simply supported at the top and bottom. Determine the maximum bending stress omax in the beams, assuming that the weight density of water is y = 9.81 kN/m³. h

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.5.27P: A small dam of a height h = 6 ft is constructed of vertical wood beams AB, as shown in the figure....

See similar textbooks

Similar questions

A small dam of a height h = 6 ft is constructed of vertical wood beams AB, as shown in the figure. The wood beams, which have a thickness I = 2.5 in., are simply supported by horizontal steel beams at A and Ä Construct a graph showing the maximum bending stress tram in the wood beams versus the depth d of the water above the lower support at B. Plot the stress0mas(psi) as the ordinate and the depth d(ft) as the abscissa. Note: The weight density y of water equals 62.4 lb/ft3.
H h V b The internal shear force V at a certain section of a beam is 60 kN.m. If the beam has a cross-section shown in the figure where h=243 mm, a=112 mm, b=182 mm, c=10,8 mm and t=14,7 mm, Determine the location of the centroid of the cross-section in the y-axis from the bottom (mm).
a y H h b The internal shear force V at a certain section of a beam is 60 kN.m. If the beam has a cross-section shown in the figure where h=243 mm, a=112 mm, b=182 mm, c=10,8 mm and t=14,7 mm, Determine the moment of inertia of the cross-section about the z-axis passes from the centroid of the section (mm*).
The horizontal beam ABC of an oil-wellpump has the cross section shown in the figure. If thevertical pumping force acting at end C is 9 kips andif the distance from the line of action of that force topoint B is 16 ft, what is the maximum bending stressin the beam due to the pumping force?
A small dam of height h= 2.0 m is constructed of vertical wood beamsAB of thickness t=120 mm, as shown in the figure. Consider the beamsto be simply supported at the top and bottom.Determine the maximum bending stress emax in the beams, assuming that the weight density of water is y= 9.81kN/M3
A beam is subjected to equal bending moments of M, = 3000 N-m. The cross-sectional dimensions areb = 190 mm, c = 30 mm, d = 73 mm, and t = 7 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. M, M2 H d (typ) K b Answer: (a) y= mm 1z = i mm4 S= i mm3 (b) ƠH = MPа ( c) σκ-1 MPа (d) Omax= MPa
The cantilever beam ABCDE is considered for supporting a concentrated force at A and a uniform distributed load at BC, as shown in the Figure. Before the dimensions of the cross-section can be determined, it is necessary to calculate the maximum shear force and maximum bending moment experienced by the beam. Do the following: 3 kN 50% 2 m B 1 kN/m 2 m Express the internal shear force and bending moment as a function of X (starting from A) D E -1 m-1 m wwwwwwwww
Determine the internal normal force and shear force, and the bending moment in the beam at points C and D. Assume the support at B is a roller. Point C is located just to the right of the 8-kip load. For your explanation section, complete a FBD of the other side of the beam from the version you did to solve the problem. 8 kip 40 kip · ft A to to D B- 8 ft 8 ft- -8 ft
poru i Henuz cevaplanmadı 5,00 uzerinden işaretlenmiş y F Soruyu işaretle H The internal shear force V at a certain section of a beam is 49,9 kN.m. If the beam has a cross-section shown in the figure where h=243 mm, a=99 mm, b=196 mm, c=10 mm and t=12,2 mm, Determine the location of the centroid of the cross-section in the y-axis from the bottom (mm). Yanıt:
If the I-flange beam is subjected to a shear force V = 20 kN, calculate the transverse shear stress at the point A (considered located on the web part). The area moment of inertia of that section about its neutral axis N.A. is INA = 44.167 x (106) m4. Flange Web Select one: O 41 MPa 10 Mpa O 4.95 MPa O O 50 MPa 100 MPa 20 mm 100 mm A 100 mm 25 mm 150 mm 25 mm
The wood beam has a rectangular cross section in the proportion shown. The allowable bending stress is o =10 MPa. 500 N/m 1.5 b B b + x m 2 m 2 m Find the reaction forces at B. O By = -250 N O By = 1000 N O By = 250 N O no reaction at B O By = 750 N
A small dam of height h=2.0m is constructedof vertical wood beams AB of thickness t =120 mm,as shown in the figure. Consider the beams to be simplysupported at the top and bottom.Determine the maximum bending stress σmax inthe beams, assuming that the weight density of wateris Υ = 9.81 kN/m3.