3 kN/m +x A B C 4.0 m 4.0 m A propped 8m prismatic beam ABCD shown in the figure is loaded with a linearly increasing load of 3kN/m until its midspan. The beam is made from a certain wood and has a rectangular cross section of 200mm width and 400mm depth and Ewood=12GPA Provide or determine the following: a. Free body diagram with a loading diagram suitable for the Macauley moment expression and the boundary conditions at point A b. The constants of integration C1 and C2 c. The vertical force reaction and moment reaction at A and the reaction at pin C

3 kN/m +x A B C 4.0 m 4.0 m A propped 8m prismatic beam ABCD shown in the figure is loaded with a linearly increasing load of 3kN/m until its midspan. The beam is made from a certain wood and has a rectangular cross section of 200mm width and 400mm depth and Ewood=12GPA Provide or determine the following: a. Free body diagram with a loading diagram suitable for the Macauley moment expression and the boundary conditions at point A b. The constants of integration C1 and C2 c. The vertical force reaction and moment reaction at A and the reaction at pin C

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.3.2P: A fixed-end b earn is subjected to a point load at mid-span. The beam has a rectangular cross...

See similar textbooks

Similar questions

A square wood column with side dimensions b (see figure) is constructed of a structural grade of southern pine for which Fc= 10,5 MPa and E = 12 GPa. An axial force P = 200 kN acts on the column. If the dimension b = 150 mm, what is the maximum allowable lensth Lmax, of the column? If the length L = 4.0 m, what is the minimum required dimension bmin?
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
A propped cantilever beam, fixed at the left-hand end A and simply supported at the right-hand end B, is subjected to a temperature differentia] with temperature T1on its upper surface and T2on its lower surface (see figure).
-15 A composite beam is constructed froma wood beam (3 in. x 6 in.) and a steel plate (3 in, wide). The wood and the steel are securely fastened to act as a single beam. The beam is subjected to a positive bending moment M. = 75 kip-in. Calculate the required thickness of the steel plate based on the following limit states: Allowable compressive stress in the wood = 2 ksi Allowable tensile stress in the wood = 2 ksi Allowable tensile stress in the steel plate = 16 ksi Assume that Ew= 1,500 ksi and es= 30,000 ksi.
A heavy object of weight W is dropped onto the midpoint of a simple beam AB from a height h (see figure). Obtain a formula for the maximum bending stress ^ma* due to tne filing weight in terms of h, st, and 5st, where it is the maximum bending stress and Sstis the deflection at the midpoint when the weight W acts on the beam as a statically applied load. Plot a graph of the ratio o"max/ö"it (that is, the ratio of the dynamic stress to the static stress) versus the ratio iifS^r(Let h/S^ vary from 0 to 10.)
A fixed-end b earn is subjected to a point load at mid-span. The beam has a rectangular cross section (assume that the h/b ratio is 2) and is made of wood (E = 11GPa). Find height h of the cross section if the maximum displacement of the beam is 2 mm. Calculate the displacement of the beam at the inflection points.
Continuous cable A DB runs over a small friction less pulley al D to support beam OABC, which is part of an entrance canopy for a building (see figure}. The canopy segment has a weight W = 1700 lb that acts as a concentrated load in the middle of segment AB. (a) What is the maximum permissible value of load P at C if the allowable force in the cable is 4200 lb? (b) If P = 2300 lb, what is the required diameter of pins A, B, and D? Assume that the pins are in double shear and the allowable shear stress in the pins is 10 ksi.
A pontoon bridge (see figure) is constructed of two longitudinal wood beams, known as bulks, that span between adjacent pontoons and support the transverse floor beams, which arc called chesses. For purposes of design, assume that a uniform floor load of 7.5 kPa acts over the chesses. (This load includes an allowance for the weights of the chesses and balks.) Also, assume that the chesses are 2.5 m long and that the balks are simply supported with a span of 3.0 m. The allowable bending stress in the wood is 15 MPa. If the balks have a square cross section, what is their minimum required width b^l Repeat part (a) if the balk width is 1.5 b and the balk depth is b; compare the cross-sectional areas of the two designs.
700N M-150UNm 2m 3m For the above dlagram, given that F, - 450 N. 0-45 degrees and d-5 m calculate the following (neglect the depth of the beam). Note that there is a pin support at A and a roller support at B. The magnitude of the horizontal component of the reaction force at A, Rar. Please provide the answer in Newtons and report to three significant figures. Please Include the unit ("N") within your answer (eg. If the calculated answer was 55.562 Newtons please Input: 55.6 N). Answer: The magnitude of the vertical component of the reaction force at A, Rar. Please provide the answer in Newtons and report to three significant figures. Please include the unit ("N") within your answer (eg. If the calculated answer was 55.562 Newtons please Input: 55.6 N). Answer: The magnitude of the horizontal component of the reaction force at B. Re. Please provide the answer in Newtons and report to three significant figures. Please Include the unit ("N") within your answer (eg. If the calculated…
A simply supported beam with a length of 4m is loaded with a uniform distributed load (w). The beam has a rectangular hollow section with the following dimensions: Outer Base = 150 mm OuterDepth 200 mm Inner Base = 100 mm Depth = 150 mm Inner Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the bending stress is limited to 8 Mpa. Please answer with solution and fbd. Thank you.
A beam of uniform rectangular section 200 mm wide and 300 mm deep is simply supported at its ends. It carries a uniformly distributed load of 9 KN/m run over the entire span of 5 m. if the value of E for the beam material is 1 X 104 N/mm2 , find the slope at the supports and maximum deflection. Give me complete solution based on the given above. Again I need to ask the same question since you gave me a wrong answer before.
DA rectangular beam 150mm wide by 250mm high carries a uniformly distributed load of 8kN/m and a concentrated load . Determine the max safe value of P if flexural stress is 10Mpa and shear stress is 1.2 Mpa