5.48 Water is sprayed radially outward over 180° as indicated in Fig. P5.48. The jet sheet is in the horizontal plane. If the jet velocity at the nozzle exit is 30 ft/s, determine the direction and magnitude of the resultant horizontal anchoring force required to hold the nozzle in place. 0.5 in. V= 30 ft/s

5.48 Water is sprayed radially outward over 180° as indicated in Fig. P5.48. The jet sheet is in the horizontal plane. If the jet velocity at the nozzle exit is 30 ft/s, determine the direction and magnitude of the resultant horizontal anchoring force required to hold the nozzle in place. 0.5 in. V= 30 ft/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A horizontal 7.5 cm diameter sharp-edged orifice with Cc = 0.063 and Cv= 0.98 is under a head of 2.30 m of water (surface is atmospheric) compute the height to which the jet of water will rise above the orifice. Include FBD. a. 3.123 m. b. 0.782 m. c. 2.208 m. d. 1.202 m.
15. A planed timber flume, rectangular in cross section is to carry 0.85cms.The depth of is to be 457mm anda width of 1.22m. What should be the slope of the flume? *
A 400cm long pipe with a smaller diameter of 3.937 inchesand a larger diameter of 11.81 inches as shown below, isinclined at a 30° angle with the horizontal. Calculate the pressure differencein KN/m²between the smaller and bigger diameter parts of the pipe if the velocity of water at the smaller diameter section is 6.56 ft/s. P₁, V₁, d₁, A₁ ₁-0- P2. V ₂. dz. Az -Datum
448. If water flows at 150 kg/s through the double wye at B,at 50 kg/s through C, and atg 50 kg/s through D, determine the average velocity of flow through the pipe at A. 250 mm 350 mm 150 mm
Q- An orifice is located in the side of a tank with its centre 10 cm above the base of the tank. The constant water level is 1.0 m above the centre of orifice. The coefficient of velocity is 0.98. On the issuing jet, find the horizontal distance from the vena-contracta to where the jet is 10 cm below vena-contracta.
A vertical semi-circular gate whose radius is ‘r’ is submerged and has its diameter in a liquid surface. Find the location of the center of pressure measured from the liquid surface. a. 0.734r b. 0.589r c. 0.823r d. 0.233r
A jet issues from the side of the tank under a head of a=4.36m. The orifice is positioned 5.94 meters above the bottom of the tank. Determine the point it strikes a horizontal plane c=1.17m below the bottom of the tank. Assume the jet will follow a projectile motion. The angle is 47 degrees and Cv=0.938.
... 2 ELEVATION 20m ELEVATION 30m AIR P ? SG-0-84 Oil flows from a tank through a 150mm diameter pipe and then discharges into air as shown. If the head loss from point 1 to point 2 is 600mm, determine the pressure needed at point 1 to cause 17L/s to flow (SG of oil = 0.84) A) 93.30 KPa B) 82.19 KPa (c) 87.74 KPa D 98.23 KPa 76.49 KPa
11- In an infinite two-dimensional flow filed, a sink of strength 3/2n m/s.m is located at the origin, and another of strength 4/2n m'/s.m at (2 , 0). What is the magnitude and direction of the velocity at point (0, 2). [0.429 m/s; -68.22°]
A jet is issued from the side of a tank under a constant head asshown in the figure. The side of the tank has an inclination of 1H:1V.The total depth of water in the tank is h1 = 6.7m and the orifice islocated at h2 = 3.7m above the bottom of the tank. The the horizontalfloor surface is at h3 = 1.2m below the bottom of the tank. If Cv = 1.0and neglecting air resistance, then Determine the maximum height (y) to which the jet will rise abovethe orifice.
Points A and B are 5km apart along a new 60cm diameter cast iron pipe carrying water. A is 9m higher than B. If the pressure at B is 140KPa greater than at A. f-0.019. [ Select ] v Determine the head loss in meters [ Select] v Determine the flow rate in lit/sec
Q2. A 600mm diameter pipeline carries water under a head of 30m with a velocity of 3m/s. This water main is fitted with a horizontal bend which turns the axis of the pipeline through 75° (i.e. the internal angle at the bend is 105°). Calculate the resultant force on the bend and its angle to the horizontal. (104.044 kN, 52° 29'] u2 u1