Match supports to reaction forces provided.                                                  Roller:                                                       Pin or knife edge:                                                       Fixed:    a.   b.   c.

Q: The figure shows a roof truss and the detail of connection at joint I. The allowable stresses are 70…

A:

Q: The figure shows a roof truss and the detail of connection at joint B. The allowable stresses are 70…

A:

Q: Determine the controlling (lowest) net area of the member. X = 2.69 Y = (6-2.69)/2 Z=0,7 Y" -X Y" 5…

A: Controlling net area

Q: 1.10-4 Lateral bracing for an elevated pedestrian walkway is shown in the figure part a. The…

A:

Q: A WT7 x 41 bracket is connected to a W14 x 159 column with 5⁄16­inch E70 fillet welds as shown in…

A: The load factor is the average load ratio to the highest demand. It depends on the value and the…

Q: A straight steel bar is fastened to a gusset plate with three 3/4-in diameter ASTM A-307 bolts, as…

A: three 3/4-in diameter ASTM A-307 boltsbolt capacity in single shear  = 7.95 kips plate capacity =…

Q: USE NATIONAL STRUCTURAL CODE OF THE PHILIPPINES 2015

A: Given that -    To determine the  net area for the plate shown in figure .   (a)   Ag = 2400×14…

Q: Question 3 Determine the capacity of plate! of plate as well as Belts (14) in the below connection…

A:

Q: Which of the following best gives the purlin load wuy? See loaded purlin. The figure shown has…

A: Answer  Roof slope (θ): tanθ = 12 θ = 26.565 degree Based on the given data, draw the tributary…

Q: Montebon, Jamaica Mae B PIate No. lo Vir tyal Work Method (Trusses) ID NG. 16-0893-335 #1. Determine…

A:

Q: Problem 1: Two plates will be connected to each other though the bolt connection or weld connection…

A:

Q: Determine the load-carrying capacity of the 2 PL 5/16 x 3 tension member shown based on the limit…

A:

Q: The following image shows a front and side view of the column connection. The bolts have a diameter…

A:

Q: snown. 7.12 A built-up steel member is composed of a W18 × 71 wide- flange section with a…

A: Given: To find: The location of the X-X axis.

Q: ind design tension strength for this connection? 12"- PL ½x8 A36 steel -Weld

A: Assuming the weld thickness bc, t=1/4 " 1)The nominal strength of fillet weld: Fw=0.6Fexx(1+0.5 Sin…

Q: 1. Identify zero force memeber. (Draw the FBD of Joint contain zero force member) B H|100 kN 60 kN K…

A: Identify the zero force member (Draw the FBD of joint contain zero force member).

Q: HW: 2-5-5 Find the tension in each of the three wires knowing that the plate has a mass of 650kg.…

A:

Q: 1.) Draw the Free-Body Diagram for each mechanism shown. Provide a direction a a name for each…

A: To draw FBD

Q: Given:  Snow: 20 psf of horizontal projection Roofing: 12 psf MC8 x 8.5 purlins Truss weight:…

A: The force of shear is a sensitive force on the surface. It's said to be the bending moment the…

Q: Draw the FBD of the link 3 & 4. What is(are) the auxiliary equation(s)?

A: cy

Q: 4/6 Determine the force in each member of the loaded truss. 45° 5m D 6m B 6m 5m 5000 N

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: The small postal scale consists of a counterweight W1, connected to the members having negligible…

A: The given figure is shown below:

Q: : Two plates will be connected to each through bolt connection or weld connection to resist the…

A: Dead load, DL=Td=300 kips Live load, LL=Tl=40 kips Wind load, WL=Tw=30 kips

Q: uired information TE: This is a multi-part question. Once an answer i owe scissors roof truss is…

A:

Q: Determine the LRFD design strength and the ASD allowable strength. Neglect block shear. A36 steel…

A:

Q: For the beam shown find the value of Force (F) Ib and maximum stress due to flexure (Ob b ) psi if…

A: Given:- The shear force in the bolts = 300 lb The shear stress in beam = 120 psi The spacing between…

Q: Only need requirements what im asking+ use given method all sokve a b c . Ok. Requirements: A.…

A: Solution: Shear force in the column: Top story: ΣFx=0P+P=35P=17.5 kN kN

Q: TOPIC : TRUSS ADALYSIS (USWE METHOO OF JONoTS) comple te one tabe. TRIALS EXPERIM ENTA L OMPUTED…

A:

Q: For the connection shown, the average shear stress in the 12-mm-diameter bolts must be limited to…

A: Diameter of bolt d = 12 mmDia of hole =12+1.5=13.5 mmAverage Shear Stress

Q: Classify each of the beams shown below as statically de terminate or statically indeterminate. If…

A: Given data in question  Structural beams  To find out  Indeterminacy  Note Ds= total Indeterminacy…

Q: Bottom chord of truss is composed of two angle bars each having a dimension of 125 mm x 67 mm x 5…

A:

Q: Given W 16x36 section as shown below (Fy = 50 ksi, Fu = 65ksi). The holes are 3/4 inch in diameter.…

A:

Q: REVISED PROBLEM: M3 HW 4 4. Six rivets are used in the connection shown in the figure. If both P =…

A: