5. Given a variable input voltage in the circuit shown, a Zener diode is used to regulate the output voltage at Vour 12 V. R-200 S2, IzK-5 mA, and IZM- 50 mA. a. Determine the minimum VIN for sustained regulation. b. Determine maximum VIN for sustained regulation. VIN(min) = R w +1₁ YOUT b) VIN(Max) =

5. Given a variable input voltage in the circuit shown, a Zener diode is used to regulate the output voltage at Vour 12 V. R-200 S2, IzK-5 mA, and IZM- 50 mA. a. Determine the minimum VIN for sustained regulation. b. Determine maximum VIN for sustained regulation. VIN(min) = R w +1₁ YOUT b) VIN(Max) =

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
How is a solid-state diode tested? Explain.
What is CEMF?
(VPP of input is 18 V. Bias voltage is 2 V. The positive peak value of output waveform for the given circuit diagram is. Diode is germanium) R1 D, VOuT VIN VsAS
Determine the value of RL that will establish maximum power conditions for the Zener diode.
A Flyback converter (for questions 1-3) shown below has the following parameters. Vin-100V, Vo-20V, Po-40W, D-0.25, Fsw-250kHz 3. What is the maximum voltage on the diode? A. 40V B. 133V C. 80V D. None of the above HE
4) Consider the following circuit. Assume that the diodes are modeled with constant offset models with Von = 1V and that the input waveform shown is applied. Sketch the corresponding waveform for Vo. Label peak values. You do not need to show your work. Vin Vin 10 -10 1K 5V D1 Vo D2
Determine minimum and maximum input voltages required for proper regulation to be performed by a Zener diode when connected across a variable input voltage. Assume Izk = 1.0mA, Izm = 120mA, Vz = 10V and series current limiting resistor Rs = 5602. Draw circuit diagram and plot graph for reverse V-I characteristic and label proper values on graph.
Q1/ +5 V +50 V V R. Vin R 47 N 3.3 kN -5 V -50 V (a) (b) a. Draw the output voltage waveform for each circuit in above figure and include the voltage values. b. What is the peak inverse voltage across each diode? c. What is the peak forward current through each diode?
Given the clamper circuit below, assume that the value of R and C are large enough so the voltage across the capacitor does not change significantly during the interval of time. a. Using the simplified diode model, simulate the action of the circuit when the diode is in forward and reverse bias condition and measure its output voltage. b. Draw the output waveform of the circuit. VIN +8V ER 1.3V. -8V
Draw the output waveform for the given circuit diagram with proper values and also mention the name of the circuit. The input waveform Vi is having a peak-to-peak value of 11 V and the bias voltage is 2 V. Assume diode to be silicon. Vo Maximum value of output waveform Minimum voltage of output waveform www
1. Draw the output voltage waveform for each circuit in Figure below and include the voltage values. N +5V +50V Vin R Va R o 0% Y 9 33k 5 Vo -5V -50v I I (@ () a. Whatis the peak inverse voltage across each diode in Figure above? b. What is the peak forward current through each diode in Figure above?