Answered: 5. A 1 cm² rod L is suspended…

5. A 1 cm² rod L is suspended vertically as shown in the figure. The unit weight of the material is y. Determine the normal stress in this rod using differential equations of equilibrium. L X у

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Strength of materials 2
A cylindrical pressure vessel having a radius r = 14 in. and wall thickness t = 0.375 in. is subjected to internal pressure p = 375 psi. In addition, a torque T = 90 kip-ft acts at each end of the cylinder (see figure). (Assume that the structures behave linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain the resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.) (a) Determine the maximum tensile stress omay and the maximum in-plane shear stress Tmay in the wall of the cylinder. (Enter the magnitudes in ksi.) o, = ksi Tmax ksi (b) If the allowable in-plane shear stress is 4.5 ksi, what is the maximum allowable torque T? (Enter the magnitude in kip-ft.) kip-ft (c) If T = 150 kip-ft and allowable in-plane shear and allowable normal stresses are 4.5 ksi and 11.5 ksi, respectively, what is the minimum required wall thickness (in inches)? in.
The d = 12-mm-diameter solid rod passes through a D = 21-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 10 mm. The rod head has a diameter of a = 29 mm, and the head has a thickness of t = 12 mm. If the normal stress produced in the rod by load P is 100 MPa, determine(a) the bearing stress acting between the support plate and the rod head.(b) the average shear stress produced in the rod head.(c) the punching shear stress produced in the support plate by the rod head. Calculate the cross-sectional area of the rod.Answer: Arod = mm2 Calculate the tension force in the rod.Answer: Frod = N Calculate the contact area between the support plate and the rod head.Answer: Acontact = mm2 Calculate the bearing stress between the support plate and the rod head.Answer: σb = MPa Calculate the area subjected to shear stress in the rod head.Answer: AV-rod head = mm2…
T·r T (from torsion) = Tr4 J ="- (Solid rod) F Onormal = A o (from bending) M•y - (Solid rod) The solid rod shown in the figure below has diameter of 1.25 in. If it is subjected to the force of 60 lb, determine the state of stress at point A using the principle of superposition. Neglect the weight of the rod, and the stress due to the I %3D I 4 transverse shear force. 60 lb k-10 in.- 15 in. Front View -20 in. В
Please give me right solution according to the question... Urgent
Solve for the equivalent force on an inclined surface. Look at Figure A.1 below. You will see a triangular block cut from a stress block with known stresses. The size and thickness of the block does not matter, so we will assume the area of the sloped inclined surface is A (sorry that it is the same symbol as the Point). If the area of the sloped surface is A, then the area of the other two surfaces is A cos (Theta) and A sin (Theta). First, draw a FBD of the block by multiplying each stress (normal and shear, known and unknown) by their associated area (in terms of A). Second, break the stress vectors on the side and bottom into components along the x’ and y’ axes. Third, sum the forces in the y’ direction and set them equal to zero (you should now be able to cross out the value of A for each term in your equation resulting in an equation with only one unknown, the normal stress in the y’ direction). Solve for the value of the normal stress in the y’ direction. Now repeat for…
Determine principal stress
. The biaxial stress system in an element is shown in the figure. Which of the following will give the normal stress in N/mm2 in the plane BD making an angle of 45° with the plane BA? 2 0₁ = 60 N/mm² C 0₂ = = 40 N/mm A A A 0₂ = = 40 N/mm 2 45 2 A B On 2 0₁ = 60 N/mm
strength of materials
A pressurized cylindrical tank with flat ends is loaded by torques T and tensile forces P (see figure). P The tank has an inner radius of r = 141 mm and wall thickness t = 6.5 mm. The internal pressure p = 7.25 MPa and the torque T = 820 N m. (Assume that the structure behaves linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain the resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.) (a) What is the maximum permissible value of the forces P if the allowable tensile stress in the wall of the cylinder is 169 MPa? (Enter the magnitude in kN.) KN (b) If forces P = 400 kN, what is the maximum acceptable internal pressure in the tank (in MPa)? MPa
None
Q3) the state of plane stress at a point is represented by the element shown below. Determine state of stress at the point on another element oriented 30° e from the position shown and show these stresses properly on the rotated element. counterClock Wise 50 MPa 80 MPa (a) 25 MPa