5- A textile plant is supplied with 3-phase, 380 VII 50 Hz source. The loads of the plant are; Number of quantity Output power Loads Power factor 60 3 kw Induction motors 0.8 lag O pf lead 0.8 lag 1 pf 50 kVAr Capacitor bank 470 kW Induction motors 8 10 kW Heater Source Calculate the total current supplied by the source and power factor of the source. 380 V Other loads Motors Lamps 6 20O

5- A textile plant is supplied with 3-phase, 380 VII 50 Hz source. The loads of the plant are; Number of quantity Output power Loads Power factor 60 3 kw Induction motors 0.8 lag O pf lead 0.8 lag 1 pf 50 kVAr Capacitor bank 470 kW Induction motors 8 10 kW Heater Source Calculate the total current supplied by the source and power factor of the source. 380 V Other loads Motors Lamps 6 20O

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

2. A voltage applied to a load is V=208420°V and current through load is I=10 &-10° A. Find the following [SO 1] o complex power consumed by load • Is the load inductive or capacitive? o the power factor of the load o the reactive power consumed or generated by the load. o Does the load consume or supply reactive power? 3. A single phase motor draws 20 kVA at 0.70 lagging power factor from a 120 V source. The PUD desires to improve the power factor to 0.9 lagging by connecting a shunt capacitor bank across the terminals of the motor. Determine the size of the capacitor bank in VARS. Calculate the following: [SO 1] a) What are the initial load current, real and reactive powers of the load? b) What are the real and reactive power after adding the capacitor bank? c) What is the kVAr rating of the capacitor bank? (3) d) What is the load current? di) How is the load current affected by the load reactive power?
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
Three load units A, B and C are connected in parallel and take currents that are respectively 12, 10 and 15 amperes. Assuming IA to be the reference phasor, IB leads IA by 30°, and IC lags IA by 65°, calculate the total current and the angle it makes with the reference.
If a A-connected load has a balanced impedance ZA 94 - 17° 2 and a voltage = = / VBC = 265 82° V rms, what is the magnitude of the current Ia (in A rms)? C V cn Van a Answer: n Von b Ia Ib 20 B IAB IBC ZA ZA ICA C
If the load is connected to the generator thgrough an inductive line and the voltage at the load side is the same as the voltage at the terminals of the generator, which of the following must be true? O A. The reactive power is flowing from the generator to the load and from load to the generator at the same time. O B. The load is disconnected, and no power is delivered to the load. O C. The load has a poor power factor and it's absorbing too much reactive power. O D. None of the other choices are correct O E. The generator is unable to produce reactive power; therefore, the reactive power is flowing from the load to the generator.
2. A cisuuit condirest of rescistance Rohm and an inductanceL henmy connected to a generator of the urrent in the ciocuit Ecoclwr ta) votrage. Fuind
Which cannot be said since Z is an inductive load in the circuit given below? A) load voltage period is 0.02sec. B) Load voltage peak value is 311V. C) Load voltage frequency is 50Hz D) Load voltage average value is 220V.
A 400 MVA synchronous machine has H, = 4.6 MJ/MVA and a 1200 MVA machine has H₂=3.0 MJ/MVA. The two machines operate in parallel in a power plant. Find out H relative to a 100 MVA base.
If a Load absorbs 10 kVA at a leading power factor of 0.6. Then the complex power is: Select one: a. -6000 - j8000 VA b. 6000 + j8000 VÀ c. 6000 - j8000 VÀ d. None of these
)Two complex loads Z1 and Z2 are connected in parallel and powered by a value voltage effective 7.2 kV and frequency 60 Hz. The first load has a power of 50 kVA and a factor of rear power of 0.9. The second charge has a power of 45 kW and a rear power factorof 0.91. Determine in steady state the kVAR power and the capacity required to correct the Total power factor to a value of 0.97 rear.
H* 3G zain IQ Asiacell The generator convert from PV to PQ if the active power of the generator exceed the * maxinum and minimum limits between the maximum and mimium limit equal to the load power Non of them With base voltage of 450 kV. The actual voltage of the generator is 560 kV. The magnitude voltage in the parameter of the PV generator in the nepaln software is * O 1.2444 pu O 450 kV O 124.44 % O 0.8036 pu 80.36 % Non of them
1980628cmid 11616 For reactive load, the power factor is equal to Select one: O a. 1 O b. 90 O c. 2 O d.0 If the voltage V, = 800 mV, then the current flowing in the primary winding Ip is: j2on Select one: O a. None of these O b. l, =40<0° mA O c.l, = 0.320<90° A O d. Ip =320<-90° mA if a Load absorbs an average power of 8 kW at a lagging power factor of 0.5 Select one: O a. -8000 + j13856.4 VA O b. None of these O c. 8000 - j13856.4 VA O d. 8000 - j13856.4 VA estion-299141-3 freactive power is