(5)25 in =A30°LABB450(6) the acceleration a"ALBC = 18 inВсTwo rigid rods areconfiguredas shown. (Cis a fixed axis of rotation,and B is a pin connection.) Given that at the instant shown, theSystem is at rest, and that the angular acceleration of rod BC isBc = 4.2 rad /s² cow, find (at this instant) :(a) the angular acceleration & of rad AB (mag and divec)ABof end A (mag and direc)

(a) Write the given data. LAB=25 inLBC=18 inαBC=4.2 rad/s2

(5) 25 in L = A 30° CA B (a) the angular acceleration (6) the acceleration a A 450 LBC = 18 in Bc configured as shown. (Cis a fixed axis of rotation, the Two rigid rods are configured. and B is a pin connection.) Given that at the instant shown, System is at rest, and that the angular acceleration of Vrod. BC is Bc = 4.2 rad /s²³ cow, find (at this instant) : of red AB (mag and divec) AB of end A (mag and direc)

(5) 25 in L = A 30° CA B (a) the angular acceleration (6) the acceleration a A 450 LBC = 18 in Bc configured as shown. (Cis a fixed axis of rotation, the Two rigid rods are configured. and B is a pin connection.) Given that at the instant shown, System is at rest, and that the angular acceleration of Vrod. BC is Bc = 4.2 rad /s²³ cow, find (at this instant) : of red AB (mag and divec) AB of end A (mag and direc)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PROBLEM 2 For the mechanism, shown on the figure, @nc = const=5s. O4-BC-0,3 m. AB 0,6 m. Determine: a) velocity and acceleration of the point B: b) angular acceleration of the body BC: c) angular velocity and angular acceleration of the body O4: d) linear velocity and acceleration of the point 4. 120
Find out the velocity of slider D and angular velocity of CD in the mechanism shown below. Take Q1A= Q2B = 2cm; Q1Q2 = 4 cm; CD = 6 cm and wQ,A rad = 1 sec Solve using instantaneous center method. Use CCW direction. 20 QI 1 A Q2 20
5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angular velocity w and angular acceleration a (both counterclockwise). 6) if W = 5.3 rad/s and Q = 7.0 rad/s?, length I = 1.8 m, and angle 0= 36°, what is the angular acceleration of link AB in rad/s?? Please pay attention: the numbers may change since they are randomized. Negative must be included if it is clockwise. Your answer must include 2 places after the decimal point. 0.5 m O, a
Q1. Member AB is rotating (about fixed point A) with angular velocity (@ = 1 rad/sec) and angular acceleration (a = 2 rad/sec?) and driving the link CD (rotating about fixed point D at constant velocity) as shown in figure. Select five right answers. (a) Tangential Acceleration (a:) of link AB will not be zero (b) Tangential Acceleration (a) of link AB will be zero D 450mm (c) Tangential Acceleration (a,) of link CD will not be zero 200 mm 100 mm 60 H (d) Tangential Acceleration (a,) of link CD will be zero (e) All points on link CB will have same linear velocity 0 All points on link CB will have same angular velocity Formula • Tangential acceleration of a rotating link -ra • Radial (normal) acceleration of a rotating link = v³ /r= wr velocity of a rotating Ink (v) = r.w (g) Angular acceleration (a) for link CD will be zero (h) Angular acceleration (a) for link CB will not be zero Q2. Magnitude of linear velocity of any point “H" located at the half of the length of a rotating link CB…
PROBLEM 2 For the mechanism, shown on the figure, @gc = const = 5 s¹₁ OA=BC=0,3 m, AB=0,6 m. Determine: a) velocity and acceleration of the point B; b) angular acceleration of the body BC; c) angular velocity and angular acceleration of the body OA; d) linear velocity and acceleration of the point A. B 120° 2000
The system shown in the figure is composed of bar AB which is pin-supported at A and attached to bar BC. The end of bar BC is connected to the slider block C. At the instant shown, the acceleration of point B is 1.125 m/s2 downward and the angular velocity of bar BC is 0.5625 rad/s counterclockwise. What is the angular acceleration of bar AB?
5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angular velocity W and angular acceleration a (both counterclockwise). 6) if W = 4.4 rad/s and a = 7.7 rad/s2, length I = 1.7 m, and angle 0= 27°, what is the angular acceleration of link AB in rad/s2? Please pay attention: the numbers may change since they are randomized. Negative must be included if it is clockwise. Your answer must include 2 places after the decimal point. 0.5 m A 0, a B Your Answer: Answer
Bar AB is pin-supported at A and attached to bar BC. The end of bar BC is connected to the slider block C. At the instant shown, the angular velocity of bar BC is 0.5625 rad/s counterclockwise, and the acceleration of point B is 1.125 m/s^2 downward. Find the following: a. Angular speed of bar AB b. Angular acceleration of bar AB c. Angular acceleration of bar BC d. Acceleration of slider block C 50 4 3 C 0.5 m B 2.0 m A
A cylinder rolls without slipping. This has an angular velocity w=0.3 rad/s and an angular acceleration w=14mrad/s, what will be the angular velocity and angular acceleration of connecting rod AB?
Link 2 of the mechanism shown rotates about the z-axis w.r.t. the ground (Link 1) at a constant +2rad/s. Link 3 rotates about a pin joint currently aligned with the y-axis at a constant -3rad/s. What is the angular acceleration of the link? Angular acceleration (rad/s^2): type your answer.... i+ type your answer... j+ type your answer.... k. Answer with integers (include zeros). Include a minus sign if necessary. Don't include a plus sign. Z 2 3
The system shown in the figure is composed of bar AB which is pin-supported at A and attached to bar BC. The end of bar BC is connected to the slider block C. At the instant shown, the acceleration of point B is 1.125 m/s2 downward and the angular velocity of bar BC is 0.5625 rad/s counterclockwise. What is the angular speed of bar AB?
5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angular velocity W and angular acceleration a (both counterclockwise). 4) if W = 4.0 rad/s and a = 6.3 rad/s2, length I = 1.5 m, and angle 0= 36°, what is the magnitude of the angular velocity of link AB? Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. 0.5 m 0, a B Your Answer: Answer units