2) A pump is being used to transport apple juice from an open tank to a second tank as shown below. The mass flow rate of the apple juice is 1 kg/s. Apple juice flows through a steel pipe with an inside diameter of 4 cm before the pump (Suction line). Density of the apple juice is 997 kg/m³. If the pipe after pump (discharge line) has a dimeter of 2.5 cm cm, what is the velocity of apple juice in discharge line?

2) A pump is being used to transport apple juice from an open tank to a second tank as shown below. The mass flow rate of the apple juice is 1 kg/s. Apple juice flows through a steel pipe with an inside diameter of 4 cm before the pump (Suction line). Density of the apple juice is 997 kg/m³. If the pipe after pump (discharge line) has a dimeter of 2.5 cm cm, what is the velocity of apple juice in discharge line?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Smnou 11. In an agricultural farm, the farmers use a sprinkler system to water the crops. The At system discharges water from a horizontal pipe at the rate of 7.20 x 10-3 one point in the pipe, where the radius is 4.00 cm (4.00 x 10-2m), the water's absolute pressure is 2.40 x 10 Pa. At a second point in the pipe, the water passes through a constriction where the radius is 2.00 cm (2.00 x 10-2m). What is the water's absolute pressure as it flows through this constriction? 12. A very ir obove the
In a liquor-bottling plant erected at a site 1 km above sea level (Patm=0.898 bar and temperature 8.7°C) where a centrifugal pump discharges 20 l/s of water against a head of 28 m while the cavita on parameter of the pump a=0.5. Where should the pump inlet location be in m with respect to the water surface.
In Fig. is shown a plot of pump net head as a function of pump volume flow rate, or capacity. On the figure, label the shutoff head, the free delivery, the pump performance curve, the system curve, and the operating point.
8. An open water tank has two inlets and one outlet. The water flow rate through the two inlets are ( 0.01 m'/s, and 0.00785 m'/s), and the water flow rate from the outlet is (0.0231 m'/s). Does the water level in the tank inereasing, decreasing, or remains constant? And if it is increasing or decreasing, at what rate this increase or decrease will occurs? Explain.
A pump is required to transfer water at the rate of 350 kg/s from an open sump to an open storage tank located 30m above the pump. The sucLon pipe is 350mm in diameter and 12m in length and the delivery pipe is 550mm in diameter and 40m in length. Calculate:(a) The maximum height at which the pump may be placed above the sump, so that pressure at the inlet is not less than -80 kPa (gauge) (b) the energy to be supplied by the pump per unit mass of water transferred (c) The input power required by the pump, which is 60 % efficient
Please include a diagram.A pump supplies water at a flow rate of 4ft3/s from an open reservoir through a horizontal 8-in sched 40 pipe. The head loss from the reservoir to the suction of the pump is 2 ft-lbf/lbm, and the discharge is at 90 psig into a 6-in sched 80 pipe. The pump has an efficiency of 65% answer the following:a.) The head that must be delivered by the pump to the water is ________ or energy developed by the pump or output energy of the pumpb.) input energy to the pumpc.) Rated power of the pump in kW
A four-stage centrifugal pump has four identical impellers, keyed to the same shaft. The shaftis running at 400 r.p.m. and the total manometric head developed by the multistage pump is 40m. The discharge through the pump is 0.2 m*3/s. The vanes of each impeller are having outlet angle as 45°. If the width and diameter of each impeller at outlet is 5cm and 60 cm respectively, Find the manometric efficiency.
Q2l Calculate size of each part for the air conditioning ducts system shown in Figure(1) by using equilibrium pressure drop method. The velocity of air in main duct 7 m/s. Tabulate the results (velocity value, rate of pressure drop, circular diameter, and air flow rate) for each part, then convert circular ducts to equivalent rectangle ducts at height 300 mm for all system. 0.5 m³/s E 5m A D 0.5m³/s 3m B Figure (1) 3m 3m 5m C 1 m³/s
A pump is used to take water out of a large lake and deliver it to a farm to be used for irrigation. The pump location is illustrated in the figure below, where the suction side of the pump (also called the pump intake) is 3 m above the water surface in the lake and the vertical intake pipe has a diameter of 150 mm. (Discharge side) Pump - >100 L/s P (Suction side) 3m -150 mm Lake Part A Assuming that viscous effects are negligible, what is the pressure on the suction side of the pump when the flow rate through the system is 100 L/s? Express your answer to three significant figures and include appropriate units.
The length and diameter of a suction pipe of a single-acting reciprocating pump are 5m and 10 cm respectively. The pump has a plunger of diameter 15cm and a stroke length of 35 cm. The center of the pump is 3 m above the water surface in the pump. The atmospheric pressure head is 10.3 m of water and pump is running at 3r rpm. Determine: a. Pressure head due to acceleration at the beginning of the suction stroke, b. maximum pressure head due to acceleration and c. pressure head in the cylinder at the beginning and at the end of the stroke
An inward flow reaction turbine has external and internal diameters as 1.095 m and 0.553 m respectively. The turbine is running at 210 R. P. M. The velocity of flow through the runner remains constant and is equal to 2.0 m/s. The width of the turbine at inlet is 241 mm. The guide blades make an angle of 10.5oto the tangent of the wheel. If the discharge of the turbine at the outlet is radial determine the following:i) Draw the inlet and outlet velocity diagramsii) The absolute velocity of the water at the inlet of the runner.iii) The velocity of whirl at inletiv) The relative velocity at inletv) The runner blade anglesvi) Width of the runner at outletvii)The hydraulic efficiency of the turbine
A centrifugal pump is used to pump a liquid with the properties given below. Liquid is pumped from a storage tank at 95 kPa (a) to a discharge tank at 300 kPa (a). The system configuration is given in the table below. Table 1: system configuration Suction Discharge 4 50 Length (m) Diameter (m) 0.07 0.055 12 90° bends (L/D-35) 5 T piece (L/D=7) Gate valve (L/D-35) 1 1 1 2 Static height (m) 25 Liquid density = 1100 kg.m³ Viscosity = 1.5 x 10-³ Pa.s Vapour pressure of the liquid = 25 kPa (a) Material of construction of pipe is commercial steel, ε = 000045 m Table 2: Pump data 0 10 20 30 40 Flowrate (m³.hr¹) Head (m) 55 56 51 36 6 NPSH (m) 0 2 6 11 19 22 3.1. Graphically determine the optimal operating point of the pump in the above system using the pump data in Table 2. 3.2. Determine the NPSH of the system and determine whether the pump will cavitate when used in the above system.